Abstract:A weighting‐factor‐free finite control set predictive torque control (FCS‐PTC) has been developed for induction motor drives by incorporating a hysteresis controller to eliminate stator flux error from the cost function. The tuning of the weighting factor coefficient in FCS‐PTC is critical for improved drive performance. The proposed method regulates the flux by incorporating a separate two level hysteresis controller and torque by the conventional cost function based PTC. The cost function uses torque error only and employs a reduced number of voltage vectors. The reduction of voltage vectors is obtained through the flux hysteresis output and sector determination. The obtained results show comparable dynamic performance of the drive with 43% lower computational burden as compared to conventional PTC. Along with computational benefits, proposed work also demonstrates improved total harmonic distortion (THD) at low speed regions due to the absence of weighting factor in cost function. This work proposes a weighting‐factor‐free finite control set predictive torque control (FCS‐PTC) for induction motor drives by incorporating a hysteresis controller to eliminate stator flux error from the cost function. The tuning of the weighting factor coefficient in FCS‐PTC is critical for improved drive performance. Conventionally, the tuning is based on an intuitive understanding of the dynamical system and empirical methods, which may not yield optimal results. The proposed method regulates the flux by incorporating a separate two‐level hysteresis controller and torque by the conventional cost function‐based PTC. The cost function uses torque error only and employs a reduced number of voltage vectors. The reduction of voltage vectors is obtained through the flux hysteresis output and sector determination. The proposed work is implemented experimentally on the dSpace DS1104 controller board for a two‐level three, three‐phase voltage source inverter‐fed induction motor drive. The experimental results validate the effectiveness of the proposed work under different drive tests compared to conventional PTC and direct torque control (DTC). The obtained results show comparable dynamic performance of the drive with 43% lower computational burden than conventional PTC. Along with computational benefit, the proposed work demonstrates improved total harmonic distortion (THD) at low‐speed regions due to the absence of a weighting factor in the cost function.

Minimization of Flux and Torque Ripples of FPOEW Induction Motor with FCS-MPTC using Synthetic Voltage Vectors

A Sequential Direct Torque Control Scheme for Seven-Phase Induction Machines Based on Virtual Voltage Vectors

Rotor Field Oriented Control Strategy with Harmonic Currents Closed-Loop Control for Five-Phase Induction Motor

Predictive Current Control for Seven-Phase Induction Motor Based on the Optimal Operating Time of Four-Dimensional Vector

A Reduced Voltage Vector Strategy-Based PTC of OEW-PMSM Drives

Novel Virtual-Finite-Control-Set-Based Model Predictive Torque Control of Five-Phase PMSM With Enhanced Third Harmonic Current Suppression

A Combined Finite Element-Domain Elimination Method for Minimizing Torque Ripples in Inverter-Fed AC Motor Drive Systems

Modulated Model Predictive Torque Control for Fault-Tolerant Inverter-Fed Induction Motor Drives With Single DC-Link Voltage Sensor

Finite Control Set Model Predictive Torque Control With Reduced Computation Burden for PMSM Based on Discrete Space Vector Modulation

Fault-Tolerant Predictive Torque Control Design for Induction Motor Drives Based on Discrete Space Vector Modulation

An Isolation Transformer-less Single DC Source fed Dual 5-leg Inverter Controlled 5-Phase Induction Motor with Modified Direct Torque Control

An Improved Model Predictive Direct Torque Control Strategy for Reducing Harmonic Currents and Torque Ripples of Five-Phase Permanent Magnet Synchronous Motors.

A Remedial Method Based on Field-Oriented Control for Five-Phase PMSM under Single-Phase Open-Circuit Fault

A Modified FOC for FTC of Induction Motor Drives

Hysteresis based predictive torque control without weighting factors for induction motor drives

Model Predictive Current Control of Nine-Switch Inverter-Fed Six-Phase Induction Motor Drives Under Healthy and Fault Scenarios

A Novel Finite-Control-Set Model Predictive Current Control for Five-Phase PM Motor with Continued Modulation

Simple predictive torque control of an open‐end winding interior permanent magnet synchronous motor drive without weighting factor for electric vehicle applications

Enhanced deadbeat predictive current control with novel generalized space vector modulation for five‐level inverter fed permanent magnet synchronous motor drive with reduced torque ripples and less computational burden

Robust Model Predictive Current Control for a Nine-Phase Open-End Winding PMSM With High Computational Efficiency

Multi Vector Predictive Current Control for Five Phase PM Motor by Using Hybrid Duty Modulation Technology