Abstract:Magnesium alloys are potentially attractive biodegradable materials. However, their rapid corrosion rate limits their biomedical application. To slow down the rate of biodegradation, a protective calcium-phosphate coating was formed on a magnesium alloy substrate by a hydrothermal method. Scanning electron microscope results showed that the coating consisted of two layers with different crystalline characteristics. The loose outer layer showed a prism-like crystal structure, while the compact inner layer is a dense ultra-fine regular di-pyramid-like structure with an average grain dimension of ∼200 nm. The compositions of the inner layer and outer layer were calcium-deficient hydroxyapatite (Ca-def HA) and dicalcium phosphate (DCPa), respectively. The coating adhered well to the substrate with a thickness of about 15 μm. Immersion in Hank’s solution indicated that the coating could significantly improve the degradation properties of magnesium alloy. The pH of the solution containing the coated samples increased much more slowly than the untreated control. After 8 d immersion, the uncoated sample had corroded seriously while the coated sample was much less corroded. The Ca/P atom ratio in both the layers of the coating increased and the coating was still protecting the substrate. The two layers of the coating corroded differently because of differences in solubility. The outer layer was more severely attacked and many holes were formed on the surface, the inner layer suffered less attack. In addition, a growth of precipitate on the inner layer was observed, indicating that surface bioactivity was improved by the coating. Thus, magnesium alloys coated with a Ca-P coating prepared by a hydrothermal method are promising candidate biodegradable biomaterials, and further investigation of in vivo degradation behavior is suggested.

Unveiling the Effect of Grain Size on Biodegradation of Magnesium

Effect of grain size and crystal orientation on the corrosion behavior of as-extruded Mg-6Gd-2Y-0.2Zr alloy

Study of grain orientation effect on the corrosion behavior of biocompatible magnesium alloy Mg-2Zn-0.5Ca

Preparing Ca-P Coating on Biodegradable Magnesium Alloy by Hydrothermal Method: in Vitro Degradation Behavior

Effect of High Deformation without Preheating on Microstructure and Corrosion of Pure Mg

Degradation Behavior of Pure Magnesium Immersed in Different Corrosive Media

Effect of grain size uniformity and crystallographic orientation on the corrosion behavior of Mg-2Zn-1Al bar

Effect of original grain size on microstructure and properties of extruded Mg-2Zn-0.2Mn biomedical alloy

Influence of Ultra-Fine Grain Structure on Corrosion Behaviour of Biodegradable Mg-1Ca Alloy

Elucidating the dependence of corrosion behavior and mechanical property on the grain structure of low-temperature as-extruded Mg–Zn–Ca–Zr alloy

The Effects of Grain Refinement and Rare Earth Intermetallics on Mechanical Properties of As-Cast and Wrought Magnesium Alloys

Study of the corrosion mechanism of Mg–Gd based soluble magnesium alloys with different initial texture states

Effect of thermal treatment on the bio-corrosion and mechanical properties of ultrafine-grained ZK60 magnesium alloy

Grain size effect on tensile properties and slip systems of pure magnesium

How surface-to-volume ratio affects degradation of magnesium: in vitro and in vivo studies

Corrosion Activity of Ultrafine-Grained Pure Magnesium and ZK60 Magnesium Alloy in Phosphate Buffered Saline Solution

Revisiting the tolerance limit of Fe impurity in biodegradable magnesium

Effects of Ultrasonic Treatment on Grain Refinement and Gas Removal in Magnesium Alloys

Corrosion Enhancement of PM Processed Magnesium by Turning Native Oxide on Mg Powders into Carbonates

Influence of the activation time of magnesium surfaces on the concentration of active hydroxyl groups and corrosion resistance

Investigating the combined effects of wide stacking faults and grain size on the mechanical properties and corrosion resistance of high-purity Mg