Abstract:Highlights • A large-scale fine-grained Mg-Gd-Y-Zn-Zr alloy plate with uniform mechanical properties was first prepared by multi-pass friction stir processing (MFSP) technology. • The transformation mechanism of LPSO phase during severe plastic deformation was revealed. • A quantitative relationship between microstructure and yield strength of Mg-Gd-Y-Zn-Zr fine-grained magnesium alloys prepared by MFSP was established. A large-scale fine-grained Mg-Gd-Y-Zn-Zr alloy plate with high strength and ductility was successfully prepared by multi-pass friction stir processing (MFSP) technology in this work. The structure of grains and long period stacking ordered (LPSO) phase were characterized, and the mechanical properties uniformity was investigated. Moreover, a quantitative relationship between the microstructure and tensile yield strength was established. The results showed that the grains in the processed zone (PZ) and interfacial zone (IZ) were refined from 50 μm to 3 μm and 4 μm, respectively, and numerous original LPSO phases were broken. In IZ, some block-shaped 18R LPSO phases were transformed into needle-like 14H LPSO phases due to stacking faults and the short-range diffusion of solute atoms. The severe shear deformation in the form of kinetic energy caused profuse stacking fault to be generated and move rapidly, greatly increasing the transformation rate of LPSO phase. After MFSP, the ultimate tensile strength, yield strength and elongation to failure of the large-scale plate were 367 MPa, 305 MPa and 18.0% respectively. Grain refinement and LPSO phase strengthening were the major strengthening mechanisms for the MFSP sample. In particularly, the strength of IZ was comparable to that of PZ because the strength contribution of the 14H LPSO phase offsets the lack of grain refinement strengthening in IZ. This result opposes the widely accepted notion that IZ is a weak region in MFSP-prepared large-scale fine-grained plate.

Investigating the combined effects of wide stacking faults and grain size on the mechanical properties and corrosion resistance of high-purity Mg

Effect of the Morphology of Long-Period Stacking Ordered Phase on Mechanical Properties and Corrosion Behavior of Cast Mg-Zn-Y-Ti Alloy

Enhanced degradation properties of Mg-Gd-Cu alloys by introducing profuse solute segregated stacking faults phase

Nanoscale coherent interface strengthening of Mg alloys

Tailoring the heterophase interfacial structures to improve both strength and ductility of Al-Li alloys by fine tuning major solute Mg

Effect of High Deformation without Preheating on Microstructure and Corrosion of Pure Mg

Grain size effect on tensile properties and slip systems of pure magnesium

Enhancing the strain hardening and ductility of Mg-Y alloy by introducing stacking faults

Simultaneous enhancement of mechanical properties and corrosion resistance of as-cast Mg-5Zn via microstructural modification by friction stir processing

A new insight into LPSO phase transformation and mechanical properties uniformity of large-scale Mg-Gd-Y-Zn-Zr alloy prepared by multi-pass friction stir processing

Enhanced superplasticity achieved by disclination-dislocation reactions in a fine-grained low-alloyed magnesium system

Unveiling the microstructure evolution and deformation mechanisms of micro-alloying Mg-1.5Zn-0.5Zr-0.5Sr alloy via extrusion-shearing

Achieving synergistic strength-ductility-corrosion optimization in Mg-Li-Al-Zn alloy via cross-pass friction stir processing

Elucidating the dependence of corrosion behavior and mechanical property on the grain structure of low-temperature as-extruded Mg–Zn–Ca–Zr alloy

Effects of electromagnetic stirring and subsequent homogenization treatment on the microstructure and mechanical properties of Al70Zn10Mg10Cu5Si5 multi-component alloy

Achieving ultra-strong Mg alloys via a novel hierarchical long-period stacking ordered architecture

Realizing ultra-fine grains and ultra-high strength in conventionally extruded Mg-Ca-Al-Zn-Mn alloys: The multiple roles of nano-precipitations

Effects of optimizing continuous forging extrusion process on the microstructure and mechanical properties of AZ31 magnesium alloy

Toward strength-ductility synergy in Al–Mg alloys: augmenting solute Mg concentration and strain-hardening ability via melt spinning and hot extrusion

Grain refinement and improved mechanical properties of Mg-4Zn-0.5Ca-0.5RE magnesium alloy by thermomechanical processing

The Effect of Morphology of the Long-Period Stacking Ordered Phase on Mechanical Properties of the Mg-7Gd-3Y-1Nd-1Zn-0.5Zr (wt.%) Alloy