Abstract:The interface morphology of the bonding layer has a considerable effect on the damage and failure of sandwich-structured thermal barrier coatings. This work investigated the comprehensive effects of a grooved texture produced using laser ablation on the local surface strain, interfacial stress and strain, and crack behavior of the bonding layer in a thermal barrier coating system. The distribution and evolution of the local surface strain was obtained using the digital image correlation method. The interfacial stress, and the strain between the ceramic and bonding layers, were determined through a simulation of the plane-strain model, and the morphology and propagation of cracks were observed in thermal barrier coatings under an external tensile load. The results indicated that the local surface strain of the thermal barrier coating increased with the texturization of the bonding layer, whereas the fluctuation decreased. There were two inflection points in the local surface strain–time curves, corresponding to the initiation of surface cracks and that of interfacial transverse cracks. The surface cracks were initiated earlier than those without the texturization of the bonding layer. However, the behavior of the interfacial cracks was more complicated. If the roughness of the texture, defined as Rc, was small, the surface cracks propagated vertically to the interface between the ceramic and bonding layers, and turned into transverse cracks, leading to a separation of the ceramic layer. If Rc was greater than 22 μm, the surface cracks went further down to the interface between the bonding layer and substrate, and propagated horizontally, resulting in the separation of both the ceramic and bonding layers. Meanwhile, interfacial cracking and separation were deferred. A large roughness resulted in good cohesion between the ceramic and bonding layers, and a high stiffness for the coating, which improved the damage resistance and extended the life of the coating.

Influence of crack and pore structure characteristics on the thermal protective performance of thermal barrier coatings based on LBM

Enhanced Thermal Isolation in Porous Thermal Barrier Coatings by the Formation of Pore Guided Thermal-Shock Cracks

Microcrack Morphology in the Thermal Insulation Performance of 8YSZ Thermal Barrier Coatings: A Mesoscale Numerical Study

Numerical Analysis of the Influence of Pore Microstructure on Thermal Conductivity and Young's Modulus of Thermal Barrier Coating

Effect of Pore Evolution on Thermal Diffusivity and Radiation Characteristics of Thermal Barrier Coatings after High-Temperature Exposures

On crack evolution with texturization of bonding layer in thermal barrier coating

Influence of Pores on the Thermal Insulation Behavior of Thermal Barrier Coatings Prepared by Atmospheric Plasma Spray

Comprehensive Understanding of Horizontal and Vertical Crack Effects on Failure Mechanism of Lamellar Structured Thermal Barrier Coatings

Mechanisms Governing the Failure Modes of Dense Vertically Cracked Thermal Barrier Coatings

Discrete element modeling of effect of interfacial roughness and pre-crack on crack propagation in thermal barrier coatings

Dominant Effect of Oriented 2D Pores on Heat Flux in Lamellar Structured Thermal Barrier Coatings

Sintering Induced the Failure Behavior of Dense Vertically Crack and Lamellar Structured TBCs with Equivalent Thermal Insulation Performance

Preparation of Long-Lifetime Thermal Barrier Coatings and Toughening Mechanism by Using Hierarchy Structured Zirconia-Based Microspheres

Interface Fatigue Crack Propagation in Ceramic Thermal Barrier Coatings

Relationship Between Pores on Thermal Sprayed Thermal Barrier Coatings and Coating Properties

A Simulation Study on the Crack Propagation Behavior of Nanostructured Thermal Barrier Coatings with Tailored Microstructure

Effect of sintering on stress distribution of thermal barrier coatings for high temperature blade

Structural Optimization for the Thermal Conductivity and Thermal Cycling Behavior in Thermal Barrier Coatings and Analysis of Thermomechanical Properties by Computational Investigation

Effect Of Periodic Surface Cracks On The Interfacial Fracture Of Thermal Barrier Coating System

Effects of sintering and mixed oxide growth on the interface cracking of air-plasma-sprayed thermal barrier coating system at high temperature

Multiscale Pores in TBCs for Lower Thermal Conductivity