Abstract:Non-equilibrium solidification and experienced thermal conditions of deposited 2219 aluminium alloy during wire and arc additive manufacturing (WAAM) result in the grain boundary segregation, which makes it difficult to avoid the appearance of columnar grain. In this work, columnar crystal defects and grain boundary segregation were eliminated by adding TiC nanoparticles (TiCnps) to WAAM-deposited 2219 aluminium alloy. The effects of TiCnps addition on the solidification dynamics, particles distribution, grain boundary structure, solute redistribution, and mechanical properties were investigated. The solidification dynamics of the droplet induced by mesoscopic TiC particles was assessed and the result showed that the addition of c. 80 nm TiCnps could reduce the solideliquid growth rate (R), besides, the critical movement rate (R-c) of 80 nmTiC(nps) was much lower than that of R, i.e. TiCnps were inclined to be distributed inside the grains as effective nucleation particles. Micro-pools with multi-site nucleation inhibited grain boundary segregation and increased Cu concentration in Al-matrix. Such a variation in Cu atom concentration promoted the precipitation of the fine spot-like theta'-CuAl2 phase with a diameter of c. 500 nm, besides, the dendritic theta-CuAl2 phase along the grain boundary was all transformed into alpha-Al+theta-CuAl2 phases with a semi-coherent state. The fine spot-like phase and TiCnps possessed a strong interfacial bonding with the Al-matrix, thereby the mechanical properties of the deposited 2219 aluminium alloy were strengthened. Eventually, the deposited 2219 aluminium alloy with the addition of TiCnps exhibited excellent mechanical properties, i.e. the tensile strength of the samples were around 380 MPa, and the elongation could be up to 21.4%. (c) 2021 The Authors. Published by Elsevier B.V. This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/4.0/).

Effect of solid solution time on microstructure and corrosion property of wire arc additively manufactured 2319 aluminum alloy

Microstructure and Mechanical Properties of 304L Steel Fabricated by Arc Additive Manufacturing

Enhanced High-Temperature Strength and Ductility of Wire Arc Additive Manufactured Al-Ce-Mg Alloys with Fine Α-Al/al11ce3 Eutectics

Microstructure evolution and mechanical properties of the wire + arc additive manufacturing Al-Cu alloy

Effects of Deposition Paramaters on the Microstructure Evolution of Wire Arc Additive Manufactured Al–Zn–Mg–Cu Alloy

Effect of grain refinement induced by wire and arc additive manufacture (WAAM) on the corrosion behaviors of AZ31 magnesium alloy in NaCl solution

Mechanical properties and precipitation behavior of the heat-treated wire + arc additively manufactured 2219 aluminum alloy

Effect of solution treatment on porosity, tensile properties and fatigue resistance of Al–Cu alloy fabricated by wire arc additive manufacturing

Improving mechanical properties of wire arc additively manufactured AA2196 Al–Li alloy by controlling solidification defects

Influence of travel speed on microstructure and mechanical properties of wire + arc additively manufactured 2219 aluminum alloy

Evolution of microstructure and properties in 2219 aluminum alloy produced by wire arc additive manufacturing assisted by interlayer friction stir processing

Realization of structural evolution in grain boundary, solute redistribution and improved mechanical properties by adding TiC<sub>nps</sub> in wire and arc additive manufacturing 2219 aluminium alloy

Microstructural Evolution and Mechanical Properties of 2219 Aluminum Alloy Deposited by Wire and Arc Additive Manufacturing

Effects of solution temperature on microstructure and mechanical properties of Al-Si-Mg aluminum alloy fabricated by wire-arc additive manufacturing

Microstructure characteristics under varying solidification parameters in different zones during CMT arc additive manufacturing process of 2319 aluminum alloy

Wire and arc additive manufacturing of dissimilar 2319 and 5B06 aluminum alloys

Effect of Different Post-heat Processes on Mechanical Properties and Corrosion Behavior of Al-Cu-Mg-Ag Fabricated by Wire Arc Additive Manufacturing

Inhomogeneity and anisotropy of Al-Zn-Mg-Cu alloy manufactured by wire arc additive manufacturing: microstructure, mechanical properties, stress corrosion cracking susceptibility

Comparative Study on Corrosion Property of 2219 Aluminum Alloy Sheet and Additively Manufactured 2319 Aluminum Alloy

The Anisotropic Corrosion Behaviour of Wire Arc Additive Manufactured Ti-6Al-4V Alloy in 3.5% NaCl Solution

Effects of Interlayer Temperature on the Microstructures of Wire Arc Additive Manufactured Al-Zn-Mg-Cu Alloy: Insights into Texture Responses and Dynamic Precipitation Behaviors