Abstract:Reverse thermally induced separation (RTIPS) was used to obtain a separation membrane with a better internal structure for a higher water flux and a surface that could easily form a hydration layer. In comparison to the traditional modification method, this work focused on the aspect that the internal structure obtained by changing the membrane-making method provided easier adhesion conditions for the dopamine/TiO<sub>2</sub> hybrid nanoparticles (DA/TiO<sub>2</sub> HNPs) obtained by biomimetic mineralization. It provided a basis for exploring the variation in adhesion with the water bath temperature and the amount of titanium added through the study of turbidity point, SEM images, water contact angle, thermogravimetric test, EDX, AFM, XPS, FTIR and other test results. The SEM images proved that the membrane obtained through the RTIPS method had a porous surface and spongy internal structure, furthermore, additional polymers were adsorbed. Use of EDX demonstrated that biomimetic mineralization prevented the production of agglomerated titanium dioxide. XPS and FTIR spectra confirmed the introduction and immobilization of HNP aggregation. Moreover, a decrease in the surface roughness and water contact angle further suggested an improvement in the hydrophilicity of the modified membrane. The introduction of HNP at a higher water bath temperature helped increase the water flux up to ten times, moreover, the oil-water separation efficiency could still reach over 99.50%. Lastly, a cycle test of the modified membrane under the optimal conditions helped confirm that the membrane forming conditions at this time could provide a better environment for the formation of the hydrophilic layer, which was conducive to the recycling of the separation membrane. In summary, more fixed more hydrophilic particles could be obtained through the RTIPS method based on biomimetic mineralization to prevent the accumulation of titanium dioxide, thus helping improve permeability and anti-fouling of the membrane.

Ultralow Ti3C2TX doping polysulfate membrane for high ultrafiltration performance

Novel polysulfone hybrid ultrafiltration membrane prepared with TiO2-g-HEMA and its antifouling characteristics

Cu-TCPP Nanosheets Blended Polysulfone Ultrafiltration Membranes with Enhanced Antifouling and Photo-Tunable Porosity

A novel polysulfate hollow fiber membrane with antifouling property for ultrafiltration application

Combing Three-Dimensional Water Channels and Ultra-Thin Skin Layer Enable High Flux and Stability of Loose Polyimide/sio2 Nanofiltration Membranes at Low Operating Pressure Via One Step In-Situ Modification

The construction of polysulfate membrane with improved ultrafiltration performance via zwitterionic copolymer segregation

Porous organic polymer nanosheets doped multistage water channel ultrafiltration membrane: Accelerated phase inversion process and in-situ covalent crosslinking strategy

Metal-polyphenol cross-linked titanium carbide membranes with stable interlayer spacing for efficient wastewater treatment

Conductive Polyethersulfone Membrane Facilely Prepared by Simultaneous Phase Inversion Method for Enhanced Anti-Fouling and Separation under Low Driven-Pressure.

High-flux and High Rejection TiO2 Nanofibers Ultrafiltration Membrane with Porous Titanium As Supporter

Preparation of TiO2/PVDF ultrafiltration membrane

Preparation of Small-Pore Ultrafiltration Membranes with High Surface Porosity by In Situ CO2 Nanobubble-Assisted NIPS

High permeability Performance TFC Nanofiltration Membrane with Two dimensional Nanochannels Support Layer Fabricated by Dissolving of Nanosheets

Polysulfone/TiO2 hybrid ultrafiltration membrane prepared by the sol-gel process

Fluoropolymer based porous membrane with Ti3C2Tx and nanocrystal-cellulose for bi-functional water treatment applications

Fabrication of polysulfone ultrafiltration membranes of a density gradient cross section with good anti-pressure stability and relatively high water flux

Performance improvement of polyethersulfone membranes with Ti3AlCN MAX phase in the treatment of organic and inorganic pollutants

A Novel Antifouling and Thermally Stable Polysulfone Ultrafiltration Membranes with Sulfobetaine Polyimide As Porogen

Tailoring of polysulfate/polyvinylpyrrolidone membrane structure via NIPS coupled physical aging technique for high-performance dye/salt separation

Polyarylester thin films with narrowed pore size distribution via metal-phenolic network modulated interfacial polymerization for precise separation

Superhydrophilic polyethersulfone (PES) membranes with high scale inhibition properties obtained through bionic mineralization and RTIPS