Abstract:Carbon fiber-reinforced polymers (CFRPs) are extensively employed in the aerospace industry due to their excellent properties. Delamination damage occurring at critical locations in CFRPs can seriously reduce the safety of in-service components. The detection and localization of delamination damage using Lamb waves hold significant potential for widespread application in non-destructive testing. However, the choice of damage localization algorithm may produce different delamination damage localization results. This research presented an IRAPID (improved reconstruction algorithm for probabilistic inspection of defects) method derived from the RAPID (reconstruction algorithm for probabilistic inspection of defects) method, aiming to improve the accuracy and reliability of delamination damage localization. Three CFRP curved plates, including a healthy curved plate and two curved plates with delamination damage sizes of Φ20 mm and Φ40 mm, were prepared in the experiment. The detection experiment of the CFRP curved plate using lead zirconate titanate (PZT) as a transducer to excite and receive Lamb waves was conducted, and the influence of excitation signal frequency on the performance of the proposed method was discussed. Under the condition of an excitation signal frequency of 220~320 kHz and a step size of 10 kHz, the accuracy of the delamination damage localization method proposed in this paper was compared with that of existing methods. The experimental results indicate that the IRAPID algorithm exhibits good stability in the localization of delamination damage across the range of frequency variations considered. The localization error of the IRAPID algorithm for delamination damage is significantly lower than that of the DaS (delay-and-sum) algorithm and the RAPID algorithm. As the size of the delamination damage increases, so does the localization error. The accuracy of delamination damage localization is lower in the X-axis direction than in the Y-axis direction. By averaging the localization results across various frequencies, we can mitigate the potential localization errors associated with single-frequency detection to a certain extent. For the localization of delamination damage, Lamb waves at multiple frequencies can be employed for detection, and the detection results at each frequency are averaged to enhance the reliability of localization.

Impact damage localization and mode identification of CFRPs panels using an electric resistance change method

A New Electrical Resistance Measurement Method of Carbon Fiber-Reinforced Polymer Tubes Based on C⁴D Technique

Review of Self-Sensing of Damage and Interfacial Evaluation Using Electrical Resistance Measurements in Nano/micro Carbon Materials-Reinforced Composites

Ultrasonic Inspection Of Localized Defects In Low-Porosity Cfrp

Impact responses and residual flexural properties of narrow CFRP laminates

Locating and Imaging Impact Damage with an Integrated System of PZT and Eddy Current Probe

Cracking Behavior of Cfrp Laminate-Strengthened Rc Beams with Premechanical and Postmechanical Environmental Damage

Characterization of the damage mechanism in CFRP composites under mode I based on comprehensive analysis of AE signals

Damage detection of FRP structures using the electrical resistance response of MWCNTs networks in a PDMS film substrate

Classification and Characterization of Damage in Composite Laminates Using Electrical Resistance Tomography and Supervised Machine Learning

Impact Damage Detection in Patch-Repaired CFRP Laminates Using Nonlinear Lamb Waves

Tensile damage self-monitoring of carbon fiber/epoxy 3D braided composites with electrical resistance method

Investigation on damage behaviors of carbon fiber‐reinforced nylon 6 thermoplastic composite laminates using acoustic emission and digital image correlation techniques

CFRP Barely Visible Impact Damage Inspection Based on Nonlinear Ultrasound Signal Sparse Reconstruction

Damage characterization and discrimination in laser-shocked carbon fiber reinforced polymer laminates: A mass-spring-damping model approach

Lightning strike-induced dynamic conduction characteristics and damage behavior of carbon fiber-reinforced polymer composites

Damage Monitoring of Regularly Arrayed Short-Fiber-Reinforced Composite Laminates under Tensile Load Based on Acoustic Emission Technology

Damage Assessment of Glass-Fibre-Reinforced Plastic Structures under Quasi-Static Indentation with Acoustic Emission

Impact damage assessment in laminated composites using acoustic emission and finite element methods

Research on Delamination Damage Localization of Carbon Fiber-Reinforced Polymer Curved Plate Using Lamb Wave

Eddy Current-Based Delamination Imaging in CFRP Using Erosion and Thresholding Approaches