Abstract:Emerging organic solar cells based on a ternary strategy is one of the most effective methods for improving the blend film morphology, absorption ability, and device performances. On the other hand, this strategy has had very limited success in all-polymer solar cells (all-PSCs) because of the scarcity of new polymers and the challenges faced during third component optimization. Herein, highly efficient ternary all-PSCs were developed from siloxane-functionalized side chains with a wide-band-gap (Eg) polymer, Si-BDT, which is blended with a medium and ultra-narrow Eg polymer donor and acceptor, PTB7-Th, and DCNBT-TPIC. An impressive power conversion efficiency (PCE) of 13.45% was achieved in the ternary all-PSCs [PTB7-Th(0.6):Si-BDT(0.4):DCNBT-TPIC(0.6)] with the addition of 0.4 wt equivalent Si-BDT into binary all-PSCs [PTB7-Th(1):DCNBT-TPIC(0.6) PCE of 10.11%]. In contrast, the binary all-PSCs with a Si-BDT(1):DCNBT-TPIC(0.6) active layer only exhibited a good PCE of 9.92%. More importantly, the siloxane-functionalized side chains increase the light-absorption ability, carrier mobility, blend miscibility, and film morphology in ternary devices compared to those of the binary devices. Hence, exciton dissociation, charge carrier transport, and suppressed recombination properties were facilitated. In the presence of Si-BDT, both binary and ternary all-PSCs PCEs are significantly improved. Indeed, 13.45% PCE is one of the best values reported for all-PSCs except for those based on polymerized small molecule acceptors. In addition, the ternary all-PSCs showed excellent environmental and thermal stabilities with 95 and 84% of the initial PCE retained after 900 and 500 h, respectively. These results offer effective device engineering, providing a new avenue for improving the device performance in ternary all-PSCs.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsami.1c20542.Additional text describing experimental details (materials and measurements and characterization of the all-PSCs), SCLC, UV–vis absorption spectra, UPS analysis, efficiency histograms, J–V curves, PL spectra, EDS element mapping, contact angle, GIXRD study, and recent publications based on ternary all-PSCs (PDF)This article has not yet been cited by other publications.

Green‐Solvent‐Processed 17% Efficient Polymer Solar Cell Achieved Synergistically by Aligning Energy Levels and Improving Morphology with the Quaternary Strategy

Ternary Strategy Enables Non‐Halogenated Solvent‐Processed All‐Polymer Solar Cells with High Efficiency Over 18%

Layer‐by‐Layer‐Processed Ternary All‐polymer Organic Solar Cells with 17.74% Efficiency Enabled by introducing a designed narrow‐bandgap guest polymer acceptor

Improved Molecular Ordering in a Ternary Blend Enables All‐Polymer Solar Cells over 18% Efficiency

18.1% Ternary All‐Polymer Solar Cells Sequentially Processed from Hydrocarbon Solvent with Enhanced Stability

Ternary Blended Fullerene‐Free Polymer Solar Cells with 16.5% Efficiency Enabled with a Higher‐LUMO‐Level Acceptor to Improve Film Morphology

Facile Strategy for Third Component Optimization in Wide-Band-Gap π-Conjugated Polymer Donor-Based Efficient Ternary All-Polymer Solar Cells

Ternary All‐Polymer Solar Cells with Efficiency up to 18.14% Employing a Two‐Step Sequential Deposition

Ternary All-Polymer Solar Cells with Two Synergetic Donors Enable Efficiency over 14.5%

Improved photon-to-electron response of ternary blend organic solar cells with a low band gap polymer sensitizer and interfacial modification

A Novel Wide‐Bandgap Polymer with Deep Ionization Potential Enables Exceeding 16% Efficiency in Ternary Nonfullerene Polymer Solar Cells

A Minimal Benzo[c][1,2,5]thiadiazole-Based Electron Acceptor As a Third Component Material for Ternary Polymer Solar Cells with Efficiencies Exceeding 16.0%

Smart Ternary Strategy in Promoting the Performance of Polymer Solar Cells Based on Bulk‐Heterojunction or Layer‐By‐Layer Structure

Chlorinated polymer solar cells simultaneously enhanced by fullerene and non-fullerene ternary strategies

Favorable Mixing Thermodynamics in Ternary Polymer Blends for Realizing High Efficiency Plastic Solar Cells

Synergistically minimized nonradiative energy loss and optimized morphology achieved via the incorporation of small molecule donor in 17.7% efficiency ternary polymer solar cells

Improving Miscibility of Polymer Donor and Polymer Acceptor by Reducing Chain Entanglement for Realizing 18.64% Efficiency All Polymer Solar Cells

All‐Polymer Solar Cells with 17% Efficiency Enabled by the "End‐Capped" Ternary Strategy

P3HT‐Based Polymer Solar Cells with 8.25% Efficiency Enabled by a Matched Molecular Acceptor and Smart Green‐Solvent Processing Technology

Achieving over 11% Power Conversion Efficiency in PffBT4T-2OD-based Ternary Polymer Solar Cells with Enhanced Open-Circuit-voltage and Suppressed Charge Recombination

Ternary Polymer Solar Cells Achieving 11.78% Efficiency with Two Fluorinated Non-Fullerene Acceptors