Abstract:The ternary polymerization strategy of incorporating different donor and acceptor units forming terpolymers as photovoltaic materials has been proven advantageous in improving power conversion efficiencies (PCEs) of polymer solar cells (PSCs). Herein, a series of low band gap nonconjugated terpolymer acceptors based on two different fused-ring electron-deficient building blocks (IDIC16 and ITIC) with adjustable photoelectric properties were developed. As the third component, ITIC building blocks with a larger π-conjugation structure, shorter solubilizing side chains, and red-shifted absorption spectrum were incorporated into an IDIC16-based nonconjugated copolymer acceptor PF1-TS4, which built up the terpolymers with two conjugated building blocks linked by flexible thioalkyl chain-thiophene segments. With the increasing ITIC content, terpolymers show gradually broadened absorption spectra and slightly down-shifted lowest unoccupied molecular orbital levels. The active layer based on terpolymer PF1-TS4-60 with a 60% ITIC unit presents more balanced hole and electron mobilities, higher photoluminescence quenching efficiency, and improved morphology compared to those based on PF1-TS4. In all-polymer solar cells (all-PSCs), PF1-TS4-60, matched with a wide band gap polymer donor PM6, achieved a similar open-circuit voltage (Voc) of 0.99 V, a dramatically increased short-circuit current density (Jsc) of 15.30 mA cm–2, and fill factor (FF) of 61.4% compared to PF1-TS4 (Voc = 0.99 V, Jsc = 11.21 mA cm–2, and FF = 55.6%). As a result, the PF1-TS4-60-based all-PSCs achieved a PCE of 9.31%, which is ∼50% higher than the PF1-TS4-based ones (6.17%). The results demonstrate a promising approach to develop high-performance nonconjugated terpolymer acceptors for efficient all-PSCs by means of ternary polymerization using two different A–D–A-structured fused-ring electron-deficient building blocks.This article has not yet been cited by other publications.

Ternary Polymer Solar Cells Achieving 11.78% Efficiency with Two Fluorinated Non-Fullerene Acceptors

Ternary Nonfullerene Polymer Solar Cells with a Power Conversion Efficiency of 11.6% by Inheriting the Advantages of Binary Cells

Ternary nonfullerene polymer solar cells with efficiency >13.7% by integrating the advantages of the materials and two binary cells

Ternary Polymer Solar Cells with Low-Cost P3HT as the Second Donor by the Complementary Absorption Region from Long-Wavelength to Medium-Wavelength Regions Forming Cascaded HOMO and LUMO Energy Levels

A Minimal Benzo[c][1,2,5]thiadiazole-Based Electron Acceptor As a Third Component Material for Ternary Polymer Solar Cells with Efficiencies Exceeding 16.0%

Ternary Polymer Solar Cells Enabled Using Two Donor Polymers with Broad Absorption and Cascade LUMO Levels

Achieving over 17% efficiency of ternary all-polymer solar cells with two well-compatible polymer acceptors

A Novel Wide‐Bandgap Polymer with Deep Ionization Potential Enables Exceeding 16% Efficiency in Ternary Nonfullerene Polymer Solar Cells

18.7% Efficiency Ternary Organic Solar Cells Using Two Non-Fullerene Acceptors with Excellent Compatibility

Chlorinated polymer solar cells simultaneously enhanced by fullerene and non-fullerene ternary strategies

Nonconjugated Terpolymer Acceptors with Two Different Fused-Ring Electron-Deficient Building Blocks for Efficient All-Polymer Solar Cells

Alloy-like ternary polymer solar cells with over 17.2% efficiency

Achieving over 11% Power Conversion Efficiency in PffBT4T-2OD-based Ternary Polymer Solar Cells with Enhanced Open-Circuit-voltage and Suppressed Charge Recombination

Nonfused Ring Electron Acceptors for Ternary Polymer Solar Cells with Low Energy Loss and Efficiency Over 18%

Semitransparent Ternary Nonfullerene Polymer Solar Cells Exhibiting 9.40% Efficiency and 24.6% Average Visible Transmittance

Charge photogeneration and recombination in ternary polymer solar cells based on compatible acceptors

Ternary Non-Fullerene Polymer Solar Cells with an Efficiency of 11.6% by Simultaneously Optimizing Photon Harvesting and Phase Separation

Synergistically minimized nonradiative energy loss and optimized morphology achieved via the incorporation of small molecule donor in 17.7% efficiency ternary polymer solar cells

Efficient Ternary Organic Solar Cells Enabled by the Integration of Nonfullerene and Fullerene Acceptors with a Broad Composition Tolerance

Over 18% efficiency ternary all-polymer solar cells with high photocurrent and fill factor

Highly Efficient Ternary All‐Polymer Solar Cells with Enhanced Stability