Abstract:<p>The self-piercing riveting (SPR) owns more advantages of acquiring high joint strength for similar and dissimilar metal sheets than the traditional spot welding. However, the conventional SPR may not obtain good joints quality for AA7075-T6 aluminum alloy sheets due to its high strength and low ductility. Thereby the possibility of self-piercing riveting under elevated temperatures makes improving the riveting quality and mechanical behavior has thus been raised as an interesting topic. In this paper, a modified thermal self-piercing riveting (T-SPR) technology for AA7075-T6 sheets was proposed based on the process that the substrate was firstly heated and conducted by the subsequent riveting and heat treatment process. The post-riveted quality and quasi-static mechanical behavior of T-SPR joints under designated temperatures were intrinsically investigated by quantifying the interlocking parameters and the single-lap shear test to assess the optimized riveting temperature. Subsequently, an improved Arcan test was employed to investigate the quasi-static mechanical behavior of cruciform joints under different loading conditions. The failure modes of cross-lap joints were analyzed in detail by combining with experiments and FE simulations coupled with Johnson-Cook (J-C) strength and damage models. The influences of loading angle and loading speed on the mechanical behavior of T-SPR joints were further discussed. The outcomes show that the joinability of T-SPR for AA7075-T6 aluminum alloys can be largely improved by increasing the riveting temperature to 400°C. The loading angle and loading speed also have a significant impact on the mechanical behaviors and failure modes of T-SPR joints under quasi-static loading conditions.</p>

Self-piercing rivetability of steel/aluminum and its improvement using reinforcing plate

Behavior and Quality Evaluation of Electroplastic Self-Piercing Riveting of Aluminum Alloy and Advanced High Strength Steel

A comparative study on self-piercing riveting and pre-holed self-piercing riveting of high-strength steel and aluminum alloy

Study on Formation and Performance of Electric-Aided Self-Piercing Riveted Aluminum Alloy and Dual-Phase Steels with Different Strength Grades

Influence of process parameters and heat treatment on self-piercing riveting of high-strength steel and die-casting aluminium

Joint Formation and Mechanical Performance of Friction Self-Piercing Riveted Aluminum Alloy AA7075-T6 Joints

Investigation of Joint Quality 980 MPa Grade GA Steel Sheet and 5052 Aluminum Alloy by Electromagnetic Self-Piercing Riveting

Mechanical Properties of B1500HS/AA5052 Joints by Self-Piercing Riveting

Thermally Assisted Self-Piercing Riveting of Aluminum AA6061-T6 to Ultra-High Strength Steels

Effect of process parameters on joint quality and mechanical properties of local-thickened self-piercing riveted steel and die-casting aluminum joints

Effect of Mechanical and Solid-State Joining Characteristics on Tensile-Shear Performance of Friction Self-Piercing Riveted Aluminum Alloy AA7075-T6 Joints

A Comparative Study of Self-Piercing Riveting and Friction Self-Piercing Riveting of Cast Aluminum Alloy Al–Si7Mg

Experimental and numerical investigation on the effect of process parameters on joint strength and failure behavior of self-piercing riveted steel/aluminium hybrid joints

Combined Strengthening Mechanism of Solid-State Bonding and Mechanical Interlocking in Friction Self-Piercing Riveted AA7075-T6 Aluminum Alloy Joints

Influence of resistance heating on self-piercing riveted dissimilar joints of AA6061-T6 and galvanized DP590

Towards joinability of thermal self-piercing riveting for AA7075-T6 aluminum alloy sheets under quasi-static loading conditions

Single-sided Joining of Aluminum Alloys Using Friction Self-Piercing Riveting (F-SPR) Process

Formation mechanism and mechanical strength evaluation of hybrid riveted/solid-state bonded aluminium alloy joint

Microstructural Evolution in Friction Self-Piercing Riveted Aluminum Alloy AA7075-T6 Joints

Effect of edge riveting on the failure mechanism and mechanical properties of self-piercing riveted aluminium joints

Effect of Process Parameters on CFRP/Steel Joints Using Self-Piercing Rivets