Abstract:Mixed usage of dissimilar materials, such as aluminum alloys and steels, has become one of the main means for vehicle body lightweighting. Due to the formation of hard and brittle intermetallic compounds in fusion welded or brazed aluminum and steel welds, resistance spot welding is hardly used. Self-piercing riveting is a preferred cold forming fastening technology and has been widely used in joining aluminum sheets and aluminum to steel sheets of multi-material vehicle bodies. However, the vast variety of stack-ups with different gauges and material properties in a body-in-white brings problems to the selection of rivets and dies. How to make the most of the rivetable range of a specific rivet and die combination is essential for not only the simplification of production line layout but also cost reduction. In this paper, seven sets of rivet and die combinations with different die-to rivet volume ratios were selected to investigate the effects of four key factors, i.e., rivet hardness, rivet length, die width and die pip height, on the rivetability and mechanical performance of the aluminum alloy AA6061-T6 and mild steel CR4. The lap-shear strength was found linearly correlated with the undercut for a fixed top sheet thickness and an equation was fitted to predict the lap-shear strength in terms of undercut and top sheet thickness. Rivetability diagrams were used to illustrate the rivetable ranges and joint quality under each set of rivet and die combinations. It was found that the softer rivets and larger dies could improve the rivetability range, meanwhile decrease the joint strength. The longer rivets and smaller dies could narrow down the rivetability range, but increase the joint strength. A die-to-rivet volume ratio of greater than 1.0 was necessary to avoid the quality issues of bottom cracking and raised rivet head for the selection of rivets and dies. These results would provide valuable reference for the determination of the riveting factors in engineering.

Effect of edge riveting on the failure mechanism and mechanical properties of self-piercing riveted aluminium joints

Mechanical Properties of B1500HS/AA5052 Joints by Self-Piercing Riveting

Effect of Mechanical and Solid-State Joining Characteristics on Tensile-Shear Performance of Friction Self-Piercing Riveted Aluminum Alloy AA7075-T6 Joints

Influence of process parameters and heat treatment on self-piercing riveting of high-strength steel and die-casting aluminium

Joint Formation and Mechanical Performance of Friction Self-Piercing Riveted Aluminum Alloy AA7075-T6 Joints

Formation mechanism and mechanical strength evaluation of hybrid riveted/solid-state bonded aluminium alloy joint

Experimental and numerical investigation on the effect of process parameters on joint strength and failure behavior of self-piercing riveted steel/aluminium hybrid joints

Effect of process parameters on joint quality and mechanical properties of local-thickened self-piercing riveted steel and die-casting aluminum joints

A Comparative Study of Self-Piercing Riveting and Friction Self-Piercing Riveting of Cast Aluminum Alloy Al–Si7Mg

The Effect of Setting Velocity on the Static and Fatigue Strengths of Self-piercing Riveted Joints for Automotive Applications

Effect of adhesive application on friction self-piercing riveting (F-SPR) process of AA7075-T6 aluminum alloy

A comparative study on self-piercing riveting and pre-holed self-piercing riveting of high-strength steel and aluminum alloy

Study of Mechanical Properties and Failure Mechanism of CFRP-Aluminum Alloy Self-Piercing Riveted-Adhesive Joints

Effect of Rivet Hardness and Geometrical Features on Friction Self-Piercing Riveted Joint Quality

Influence of thickness combinations on mechanical properties of joints produced by clinch riveting with rigid rivet

Effect of Rivet and Die on Self-Piercing Rivetability of AA6061-T6 and Mild Steel CR4 of Different Gauges

Effects of process parameters on friction self-piercing riveting of dissimilar materials

Behavior and Quality Evaluation of Electroplastic Self-Piercing Riveting of Aluminum Alloy and Advanced High Strength Steel

Equivalent characterization of pre-strained material properties and mechanical behavior prediction of steel/aluminum self-piercing riveted joints

Single-sided Joining of Aluminum Alloys Using Friction Self-Piercing Riveting (F-SPR) Process

A Comparative Study of Friction Self-Piercing Riveting and Self-Piercing Riveting of Aluminum Alloy AA5182-O