Abstract:Mechanical strengthening mechanism of pre‐embedded adhesive in the rivet cavity. Self‐piercing riveted bonded (SPRB) joints are widely used in body‐in‐white (BIW) to connect dissimilar materials owing to their high fatigue and electrochemical performance. However, the strength of the SPRB joint has been found to be inferior to that of self‐piercing riveted (SPR) joints, owing to the reduction in undercut induced by the introduction of an adhesive, especially under pull‐out loading conditions. Interestingly, the mechanical strength improved when the rivet cavity was pre‐embedded with an adhesive. Before the riveting process, the rivet cavities in SPRB joints were pre‐embedded with 0.01, 0.02, and 0.03 mL of adhesive, namely them PSPRB‐V1–V3, respectively. Finite element (FE) models of SPRB and PSPRB joints were developed to analyze their formability and mechanical properties. The simulated and experimental results showed that the hydraulic pressure in the rivet cavity increased as the pre‐embedded adhesive volume in the rivet cavity increased during the riveting process, which further improved the undercut, microhardness, effective bearing area, and mechanical properties of joints. Among the prepared PSPRB joints, the PSPRB‐V3 joint exhibited the best undercut and optimal mechanical properties. Specifically, its undercut and peak force increased by 16.43% and 12.87% compared with those of SPRB joints. These findings provide important guidance for designing steel‐aluminum SPRB joints that require high‐bearing capabilities. Highlights The effect of pre‐embedded adhesive on the SPRB joint cross‐section was studied. Failure mechanisms of the SPRB and PSPRB joints were investigated via FEM. The better PSPRB joint performance over SPRB joints was elucidated. The stress–strain history was considered in the FE model of the joint failure process. Strengthening mechanism of pre‐embedded adhesive in the rivet cavity was discussed.

Effect of Process Parameters on CFRP/Steel Joints Using Self-Piercing Rivets

Effect of process parameters on joint quality and mechanical properties of local-thickened self-piercing riveted steel and die-casting aluminum joints

Low-frequency vibration assisted self-pierce riveting (LV-SPR) of carbon fiber reinforced composite and aluminum alloy

Experimental and numerical investigation on the effect of process parameters on joint strength and failure behavior of self-piercing riveted steel/aluminium hybrid joints

Experimental study on dynamic behavior of CFRP-to-steel interface

Influence of process parameters and heat treatment on self-piercing riveting of high-strength steel and die-casting aluminium

Self-piercing rivetability of steel/aluminum and its improvement using reinforcing plate

A comparative study on self-piercing riveting and pre-holed self-piercing riveting of high-strength steel and aluminum alloy

Analysis of joint formation mechanisms for self-piercing riveting (SPR) process with varying joining parameters

Mechanical Properties of B1500HS/AA5052 Joints by Self-Piercing Riveting

Investigation of Joint Quality 980 MPa Grade GA Steel Sheet and 5052 Aluminum Alloy by Electromagnetic Self-Piercing Riveting

Effect of Bushing Structure on Mechanical Properties and Failure Mechanism of CFRP Laminated Titanium Nail Riveting

Effect of adhesive application on friction self-piercing riveting (F-SPR) process of AA7075-T6 aluminum alloy

Fatigue strength of self-piercing riveted joints of carbon fiber reinforced composite and Al5052 alloy plates

Study of Mechanical Properties and Failure Mechanism of CFRP-Aluminum Alloy Self-Piercing Riveted-Adhesive Joints

Numerical investigation of joinability and forming quality improvement on self-piercing riveting process with varying sheet stack combinations

Double-sided self-pierce riveting: analysis of the mechanisms behind the chamfered angle position

Effects of Service Temperature on the Mechanical Properties of CFRP/Aluminum Alloy Self-Piercing Riveting Joints

Reinforcement and toughening of the self‐piercing riveted bonded joints induced by the pre‐embedded adhesive in rivet cavities

Equivalent characterization of pre-strained material properties and mechanical behavior prediction of steel/aluminum self-piercing riveted joints

The Effect of Setting Velocity on the Static and Fatigue Strengths of Self-piercing Riveted Joints for Automotive Applications