Abstract:The divertor of the China Fusion Engineering Test Reactor (CFETR) requires a more efficient heat dissipation structure due to the high demand of heat flux dissipation of up to 20 MW/m 2 . Microchannel cooling technology excels in thermal management because of large heat transfer area to volume ratio and capability to achieve uniform temperature distribution. However, the heat transfer and thermal fatigue characteristics of W/Cu flat type mock-up with microchannel cooling structures at a heat flux of 20 MW/m 2 remains elusive. In this work, we analyzed the thermohydraulic (numerically) and thermal fatigue (experimentally) characteristics of W/Cu flat-type microchannel mock-up. The numerical results show that the thermal loaded area (W) of the microchannel mock-up possesses excellent temperature uniformity and heat transfer performance (the W surface temperature is only ∼685 °C even at a low volumetric flow rate V̇ = 5 L/min). We also compared the heat dissipation efficiency with the hypervapotron cooling channels, and found that the maximum temperature of the W surface and channel wall of the microchannel mock-up are reduced by 18.9 % and 46.7 %, respectively. The thermal stress analysis indicates that the maximum equivalent stress is concentrated in the middle region of the W surface at 15 s, with a value of 357.8 MPa that is below the maximum allowable stress of W material (425 MPa at 650 °C). The as-manufactured W/Cu flat-type microchannel mock-up successfully withstood a thermal fatigue test consisting of 1000 cycles at 20 MW/m 2 steady state heat load at V̇ = 30 L/min and T in = 25 °C. The maximum temperature of W is only 616.2 °C during the test, and some microcracks are detected on the W surface after the test; these microcracks are perpendicular to the heat loading surface, which have negligible influence to the heat transfer of the entire mock-up. This study reveals that the W/Cu flat-type microchannel mock-up is promising in dissipating ultra-high heat flux (steady-state 20 MW/m 2 ) on the divertor target, which might provide valuable insights for the engineering design of the CFETR divertor.

Reliability research of hypervapotron under electromagnetic load for CFETR divertor

Preliminary Thermo-hydraulic and Mechanical Analysis for CFETR Divertor

Engineering Conceptual Design of CFETR Divertor

Estimation of Peak Heat Flux Onto the Targets for CFETR with Extended Divertor Leg

A Study on Nuclear Analysis of the Divertor Region of the CFETR

Simulation Study on Detachment Operation of Snowflake Divertor for CFETR

Edge Localized Mode Characteristics and Divertor Heat Flux During Stationary and Transient Phase for CFETR Hybrid Scenario

Engineering Design and Analysis of the CFETR Divertor Remote Maintenance System

Analysis of nuclear response in CFETR toroidal field coils with density reduction VR technique

Study of W/Cu Flat-Type Mock-Ups with Novel Hypervapotron Cooling Structure for CFETR Divertor

Progress, Load Study, and Structural Analysis of the CFETR Divertor Dome

Electromagnetic load evaluating and optimizing approach of the blanket system during VDEs considering halo current

Simulation Studies of Divertor Power Exhaust with Neon Seeding for CFETR with GW-level Fusion Power

Thermohydraulic and thermal fatigue characteristics of W/Cu flat-type microchannel mock-up for CFETR divertor

Predictive Modeling for Performance Assessment of ITER-Like Divertor in China Fusion Engineering Testing Reactor

Front-Face RH Compatible Structure Design and Thermal Analysis for CFETR Divertor Dome

Modeling of Divertor Geometry Effects in China Fusion Engineering Testing Reactor by Solps/B2-Eirene

Study on Creep Fatigue of Heat Sink in W/RAFM Divertor for CFETR

ICONE23-1882 SOLPS MODELLING OF DETACHMENT IN LOWER SINGLE-NULL DIVERTOR FOR CHINA FUSION ENGINEERING TESTING REACTOR

Evaluation of electromagnetic forces on Chinese Dual Functional Lithium Lead Test Blanket Module in ITER

Multiscenario Electromagnetic Load Analysis of Blanket and VV for CFETR