Abstract:The influence of asymmetric rolling on the microstructure, texture and mechanical properties of Al–Mg–Si alloy was investigated comprehensively through finite element simulation (FEM), microstructure and texture characterization, and tensile testing. Cold rolling was applied by imposing different velocity ratios (from 1 to 1.75) between the upper and lower rolls. The results show that asymmetric rolling has some effects on the shear strain, microstructure, texture and mechanical properties. The shear strain always exhibits a non-uniform distribution throughout the sheet thickness, and it is closely related to the velocity ratio; improving the velocity ratio could result in a larger shear strain in the surface contacting the roll with a higher velocity. As the velocity ratio increases, the cold rolled alloy sheet contains an increasing number of fine equiaxed grains, and the solution-treated recrystallization grain structure gradually becomes fine. Unlike symmetric rolling, asymmetric rolling can result in the development of TD-rotated β fiber, and the rotation angle is largely dependent on the velocity ratio. Although no ideal shear texture E {111}<110> and F{111}<112> orientations were developed, the shear texture H{001}<110> orientation appears by applying a sufficient velocity ratio. After solution treatment, the velocity ratio has no influence on the texture component, but improving the velocity ratio can reduce the texture volume fraction. Asymmetric rolling plays a positive role in improving mechanical property. As the velocity ratio increases, there are increases in the strength, elongation and plastic strain ratio R, and a decrease in the planar anisotropy ΔR, which is likely attributable to the weak texture.

Texture transition of shear bands in initially Goss–oriented grains in Fe–3 wt%Si alloy

Evolution of the Shear Band in Cold-Rolling of Strip-Cast Fe-1.3% Si Non-Oriented Silicon Steel

Through Thickness Variation of Cross Shear Rolling Texture in Grain Oriented Silicon Steel

Experimental investigation and simulation of crystallographic orientations evolution in a cold-rolled ultra-thin grain-oriented silicon steel

Microstructure, Texture Evolution And Magnetic Properties Of Fe-6.5 Wt. % Si And Fe-6.5 Wt. % Si-0.5 Wt. % Cu Alloys During Rolling And Annealing Treatment

Formation and Growth of Cubic Grains During Rolling-Annealing Process in Fe-3.2%Si Alloy

A quasi-in-situ EBSD study on the formation and development of η-fiber in 0.15 mm ultra-thin Fe-4.5 wt. % Si sheet

Microstructure and Texture Evolution of Strip-Cast and Hot-Rolled Fe-3 %si Steel Sheet

Texture Evolution during Recrystallization and Grain Growth in Non-Oriented Electrical Steel Produced by Compact Strip Production Process

TEXTURE CHARACTERISTICS OF Fe-6.5%Si SHEETS PRODUCED BY THE DEPOSITIONDIFFUSION METHOD

Effects of Strain Rate on Shear Bands and Texture Evolution in Grain-oriented Silicon Steel

TEXTURE DISTRIBUTION AND DEVELOPMENT THROUGH THE THICKNESS AFTER CROSS SHEAR ROLLING OF GRAIN ORIENTED SILICON STEEL

Dislocation Strengthening and Texture Evolution of Non-Oriented Fe-3.3 wt% Si Steel in Double Cold Rolling

EFFECT OF COLD ROLLING PROCESS ON TEXTURE EVOLUTION OF GRADIENT MICROSTRUCTURE IN Fe-3,0 % Si NON-ORIENTED SILICON STEEL

Influence of Asymmetric Rolling on the Microstructure, Texture Evolution and Mechanical Properties of Al–Mg–Si Alloy

Electron Backscatter Diffraction Analysis of Low-Misorientation-Angle Boundary and High-Energy Boundary in the Hot-Rolled Plate of Grain-Orientated Silicon Steel

On the influence of austenite content in orientation selectivity and shear texture evolution during hot rolling of Fe-3 wt% Si grain-oriented electrical steel

Micro-Crystallographic Analysis of Shear Band Formation Mechanism in Cold Rolled Al-Sc Alloys at Different Precipitation States

The Early Stage Formation of Shear Orientations and the Stability of //ND Orientations During Hot Rolling in Electrical Steels

A comprehensive study on texture evolution and recrystallization mechanism of Fe-4.5 wt% Si with strong {114}

Microstructural evolution and magnetic properties in strip cast non-oriented silicon steel produced by warm rolling