Abstract:The paper reports the main features of electrochemical deposition of nickel-iron alloy from electrolyte based on the eutectic mixture of choline chloride and ethylene glycol, which is a typical representative of a new type of ionic liquids, deep eutectic solvents (DES). It is found that the iron content in the deposited alloy increases with both increasing the applied cathode current density and increasing the concentration of iron ions in the electrolyte and the introduction of water additives. Thus, variation in the current density and the concentration of water additive in electrolytes based on DES is the factor of influence on the kinetics of partial electrode reactions, and hence on the composition and properties of the coating. It is shown that it is possible to deposit uniform coatings with iron content up to 10–13% from the investigated electrolyte containing water additive (up to 10 wt.%) at the deposition current density not exceeding 1–1.2 A/dm2. The current efficiency of the alloy deposition is close to the theoretical value (97–99%), i.e. the electrodeposition is practically not complicated by electrochemical processes involving components of a deep eutectic solvent. The surface of pure nickel deposited from an electrolyte based on DES without additional water is quite uniform with a small number of defects, pitting and small pores, while coatings deposited from the electrolyte containing water additives are characterized by granular surface morphology with many asymmetric spheroidal crystallites. The electrodeposition of a nickel-iron alloy yields the surface built of irregular spheroids that overlap and form a scaly-like type of surface morphology. Nickel-iron electrolytic coatings containing up to ~7% Fe, formed from the ethaline-based electrolyte, are nanocrystalline solutions of iron in nickel with a face-centered cubic nickel lattice and an average nanocrystallite size of about 6–15 nm. Nickel-iron alloy coatings electrochemically deposited under the conditions established in this work may be considered as promising electrode materials for the creation of new cheap and highly efficient electrocatalysts for water electrolysis in hydrogen energy.

Long-life Electroless Nickel Process by Continuous Regeneration with Electrodialysis

Electrochemical reactor with rotating cylinder electrode for optimum electrochemical recovery of nickel from plating rinsing effluents

The Application of Electrodialysis to Extend the Lifetime of Commercial Electroplating Baths

A Comparative Study Of Nickel(Ii) Removal From Electroplating Wastewater By Pre-Precipitation Combined With Fenton-Precipitation Or Fenton-Like-Precipitation

Selective recovery of Nickel from electroplating rinse bath wastewater by an integrated Donnan Dialysis/precipitation process

Highly efficient nickel recovery from industrial wastewater via synergistic electrodeposition and electrocatalytic oxidation technique

Electrocatalysis coupled super-stable mineralization for the efficient treatment of phosphorus containing plating wastewater

Removal of low concentrations of nickel ions in electroplating wastewater by combination of electrodialysis and electrodeposition

Approaches to Enhancing Cathodic Nickel Recovery from Ni-EDTA Containing Synthetic Wastewaters

Optimisation of parameters of complete nickel electrodeposition from acidic aqueous electrolytic baths prepared by dissolution of metal powder

Recovery of nickel from electroless nickel plating wastewater based on the synergy of electrocatalytic oxidation and electrodeposition technology

Recovery of Ni(II) from Real Electroplating Wastewater Using Fixed-Bed Resin Adsorption and Subsequent Electrodeposition

A new environmentally friendly non-destructive activation process of electroless nickel plating on alumina ceramics

Optimizing Nickel Electroplating in Low-Ni Environments for Efficient Source Production in Small Plating Baths

Novel Electroless Nickel Plating Process

ELECTRODEPOSITION OF NANOCRYSTALLINE NICKEL-IRON ALLOY FROM AN ELECTROLYTE BASED ON A NEW TYPE OF IONIC LIQUIDS – DEEP EUTECTIC SOLVENT

Optimisation of Nickel Electrodeposition Solutions for Power Usage

Industrial-scale highly efficient nickel recovery from electroplating wastewater using resin adsorption followed by aeration mixing acid regeneration

Nickel Speciation of Spent Electroless Nickel Plating Effluent along the Typical Sequential Treatment Scheme.

TREATMENT AND REUSE OF NICKEL PLATING RINSING WATER BY ION EXCHANGE PROCESS

A Method for Electroless Nickel Plating on Aluminum Alloy Surface