Abstract:This work marks the third in a series of experiments that were in a semi-circular, gas-fluidized bed with side jets. In this work, the particles are 1 mm ceramic beads. The bed is operated just at and slightly above and below the minimum fluidization velocity and additional fluidization is provided by two high-speed gas located on the sides of the bed near the flat, front face of the unit. Two primary measurements are taken: high-speed video recording of the front of the bed and bed pressure drop from a tap in the back of the bed. PIV is used to determine particle motion, characterized as a mean Froude number, from the high-speed video. A CFD-DEM model of the bed is presented using the recently released MFIX-Exa code. Four model subvariants are considered using two methods of representing the jets and two drag models, both of which are calibrated to exactly match the experimentally measured minimum fluidization velocity. Although it is more difficult to determine the jet penetration depths in a straightforward manner as in the previous works using Froude number contours, the CFD-DEM results compare quite well to the PIV measurements. Unfortunately, the good agreement of the solids-phase is overshadowed by significant disagreement in the gas-phase data. Specifically, the predicted time-averaged standard deviation of the pressure drop is found to be over an order of magnitude larger than measured. Due to the low value of the measurements, just 1% of the mean bed pressure drop, it seems possible that the data is in error. On the other hand, the model may not be accurately capturing pressure attenuation through an under-fluidized region in the back of the bed. Without the possibility additional experiments to test the validity of the data, this work is simply being reported as is without being able to indicate which, either the simulation or the experiment, is more correct.

CPFD study of volatile liquid injection in a dense gas–solid fluidized bed

A Volatile Spray Zone Model and Experimentation in a Gas-Solid Fluidized Bed with Liquid Injection

CFD Simulation of an Agitated Gas-Fluidized Bed: Effects of Particle–particle Restitution Coefficient on the Hydrodynamics

Experimental and numerical investigation of solid behavior in a gas–solid turbulent fluidized bed

Distribution and Movement of Fine Particles Injected in a Gas–solid Fluidized Bed with Hydrocarbon Liquid Spray

Hydrodynamics and Heat Transfer in a Fluidized Bed with Liquid Spray: Particle Color-Change Based Measurement and Modelling

Experimental Investigation of Bubble and Particle Motion Behaviors in A Gas-Solid Fluidized Bed with Side Wall Liquid Spray

Dynamic and Steady-State Characterization of the Liquid Spray Zone in an Externally Heated Gas–Solid Fluidized Bed

Experimental and Modeling Investigation of Liquid-Induced Agglomeration in a Gas–Solid Fluidized Bed with Liquid Spray

Numerical Study of Particle Injection into a Gas-Solid Fluidized Bed

Investigating Agglomeration Behaviors in High Temperature Gas–Solid Fluidized Beds with Liquid Injection

Particle Fluidization Characteristics and Transition in a Hot Gas-Solid Fluidized Bed with Liquid Injection

Dispersion Trajectory and Dynamics of Particles Injected from the Sidewall in the Gas–Solid Fluidized Bed

Dynamic Characteristics of the Volatile Cloudy Zone in a Gas–solid Fluidized Bed with Hydrocarbon Liquid Spray

Predicting cold gas-solid flow in a pilot-scale dual-circulating fluidized bed: Validation of computational particle fluid dynamics model

Injection of gas–liquid jets into gas–solid fluidized beds: A review

Experimental investigation of cavity stability for a gas-jet penetrating into a liquid sheet

Experiment and simulation of high-speed gas jet penetration into a semicircular fluidized bed

Optimizing injection modes and reactor shapes in gas-particle fluidized beds using a mesoscale CFD model

CPFD Simulation of Gas-Solid Flow in Dense Phase Zone of Pant-Leg Fluidized Bed with Secondary Air

Real-fluid injection modeling and LES simulation of the ECN Spray A injector using a fully compressible two-phase flow approach