Abstract:The transition section between bottom dense zone and top dilute zone is important for fast gas-solids catalytic reactions,such as methanol to olefins(MTO).Solids concentration and fluctuation parameters in the transition section of a fluidized bed with 95 mm i.d.were measured by using reflective optical fiber probe(PV6D).The influences of superficial gas velocity and static bed height were investigated.An Eulerian-Eulerian two-fluid model that incorporated kinetic theory of granular flow and modified three-zone drag law was used to predict the flow structure in the turbulent fluidized bed.The axial and radial distributions of solids concentration were simulated by means of computational fluid dynamics(CFD).The experiments showed two axial profiles of solids distribution in the transition section:exponential and S-shaped.The maximum gradients of both axial and radial solids concentration profiles were located in the transition section,which meant that solids distribution in the transition section was much more non-uniform than that in the dilute and dense sections.The change of gas velocity and static bed height would cause a shift between exponential and S-shaped profiles,and significantly affect solids concentration in the dense region near the wall and at the bottom.Probability density distribution of local solids concentration revealed that when static bed height was small,the location of maximum voidage would gradually move from core region to annular region with increasing gas velocity,resulting in a bimodal distribution of voidage.A modified three-zone drag model was proposed by taking the effect of particle clustering into account for CFD simulation.The simulated solids concentration distribution agreed well with experimental data in the transition section except for the distributor zone.

Distribution and Movement of Fine Particles Injected in a Gas–solid Fluidized Bed with Hydrocarbon Liquid Spray

Dynamic Characteristics of the Volatile Cloudy Zone in a Gas–solid Fluidized Bed with Hydrocarbon Liquid Spray

Experimental Investigation of Bubble and Particle Motion Behaviors in A Gas-Solid Fluidized Bed with Side Wall Liquid Spray

Hydrodynamics and Heat Transfer in a Fluidized Bed with Liquid Spray: Particle Color-Change Based Measurement and Modelling

Experimental and Modeling Investigation of Liquid-Induced Agglomeration in a Gas–Solid Fluidized Bed with Liquid Spray

Dispersion Trajectory and Dynamics of Particles Injected from the Sidewall in the Gas–Solid Fluidized Bed

A Volatile Spray Zone Model and Experimentation in a Gas-Solid Fluidized Bed with Liquid Injection

Dynamic and Steady-State Characterization of the Liquid Spray Zone in an Externally Heated Gas–Solid Fluidized Bed

Experimental and Numerical Study of Solids Concentration Distribution in Transition Section of Turbulent Fluidized Bed

Investigating Agglomeration Behaviors in High Temperature Gas–Solid Fluidized Beds with Liquid Injection

Particle Fluidization Characteristics and Transition in a Hot Gas-Solid Fluidized Bed with Liquid Injection

Characterization of Flow Pattern of Cohesive Particles in Gas-Solid Fluidized Bed Via Axial Distribution of Particle Motions

Mass Transfer Characterization for Hydrocarbon Liquid–particle Collision Based on Sensitive Tracing of Fluorescent Probe

Numerical Study of Particle Injection into a Gas-Solid Fluidized Bed

Multi-scale Characteristics and Gas-Solid Interaction among Multiple Beds in a Dual Circulating Fluidized Bed Reactor System

Classification and Identification of Gas–liquid Dispersion States in a Jet Bubbling Reactor

Particle Motion in Two‐ and Three‐Phase Fluidized‐Bed Reactors Determined by Pulsed Field Gradient Nuclear Magnetic Resonance

Effects of liquid action mechanisms on hydrodynamics in liquid-containing gas–solid fluidized bed reactor

Bubble Dynamics and Particle Orientation in a Binary Fluidized Bed Containing Spherocylinders and Spheres

Effects of Interparticle Forces on Fluidization Characteristics in Liquid-Containing and High-Temperature Fluidized Beds

Simulation of Droplet-gas Flow in the Effervescent Atomization Spray with an Impinging Plate