Abstract:A novel solvent‐assisted hydrothermalmethod for fabricating high‐quality Sb2(S,Se)3 thin films and high‐performance (10.75%) solar devices is demonstrated, which not only contributes to improving component(S/Se), morphology, crystallization, and photoelectric properties of the absorber layer but also plays an important role in reducing defects at a deep level. Antimony chalcogenides (Sb2(SxSe1−x)3, 0 < x < 1) have recently gained popularity due to their excellent photoelectric properties. As a newcomer to thin‐film solar cells, the quality of the as‐prepared absorb layer remains the most difficult challenge, owing to its distinct crystal structure. Here, a solvent‐assisted hydrothermal deposition (SHD) technique is developed for direct deposition of high‐quality Sb2(S,Se)3 films; it is realized that the addition of ethanol can regulate the reaction kinetics by regulating the concentration of the Sb source during the deposition procedure. Impressively, under such conditions, the deposition rate of the target absorb layer slows dramatically, resulting in more suitable features, such as large grain size, smooth surface, and proper bandgap, which are beneficial for constructing high performance solar devices. More importantly, using this newly developed SHD strategy, the defect (SbS1) density of the prepared films decreases by more than one order of magnitude, which is believed to benefit carrier transport. As a result, Sb2(S,Se)3 solar cells based on the SHD strategy significantly improve fill factor and short‐circuit current density, yielding a high efficiency of 10.75%. This research offers fresh insights into how to make Sb2(S,Se)3 films and solar cells of higher quality.

Theoretical Studies on Surface Kinetics and Growth Properties of Sb 2 Se 3 and Sb 2 S 3

Theoretical studies on surface kinetics and growth properties of Sb<sub>2</sub>Se<sub>3</sub> and Sb<sub>2</sub>S<sub>3</sub>

Ten Years of Sb2Se3 Thin Film Solar Cells

Structure, Morphology, and Photoelectric Performances of Te-Sb<sub>2</sub>Se<sub>3</sub>Thin Film Prepared via Magnetron Sputtering

Structure, Morphology, and Photoelectric Performances of Te-Sb 2 Se 3 Thin Film Prepared via Magnetron Sputtering.

Structure, Morphology, and Photoelectric Performances of Te-Sb<sub>2</sub>Se<sub>3</sub> Thin Film Prepared via Magnetron Sputtering

10 Years of Sb 2 Se 3 Thin Film Solar Cells

Postsurface Selenization for High Performance Sb2S3 Planar Thin Film Solar Cells

Chemical Etching Induced Surface Modification and Gentle Gradient Bandgap for Highly Efficient Sb2(S,Se)3 Solar Cell

Electronic and optical properties of Sb 2 Se 3 and Sb 2 S 3 : theoretical investigations

In Situ Sulfurization to Generate Sb2(Se1 − Xsx)3 Alloyed Films and Their Application for Photovoltaics

Sb-2(Se1-xSx)(3) Thin-Film Solar Cells Fabricated by Single-Source Vapor Transport Deposition

Scalable and efficient Sb2S3 thin-film solar cells fabricated by close space sublimation

Characterization of Basic Physical Properties of Sb 2 Se 3 and Its Relevance for Photovoltaics

Sb2Se3 Solar Cells Fabricated Via Close-Space Sublimation

Solvent‐Assisted Hydrothermal Deposition Approach for Highly‐Efficient Sb2(S,Se)3 Thin‐Film Solar Cells

Thermally Deposited Sb2Se3/CdS-Based Solar Cell: Experimental and Theoretical Analysis

Research progress on tunable band gap antimony sulfoselenide thin films and solar cells

Investigation of electronic transport mechanisms in Sb2Se3 thin-film solar cells

Unveiling the Influence of Absorber Thickness on Efficient Sb2(S, Se)3 Solar Cells Through Controlled Chemical Bath Deposition

Solution‐Processed Sb2(S, Se)3 Seeds‐Assisted Sb2Se3 Thin Film Growth for High Efficiency Solar Cell