Abstract:The ecofriendly tin selenide (SnSe) is expected to find multiple applications in optoelectronic, photovoltaic, and thermoelectric systems. This work is focused on the thermoelectric properties of thin films. SnSe single crystals exhibit excellent thermoelectric properties, but it is not so in the case of polycrystalline bulk materials. The investigations were motivated by the fact that nanostructuring may lead to an improvement in thermoelectric efficiency, which is evaluated through a dimensionless figure of merit, ZT = S2 σ T/λ, where S is the Seebeck coefficient (V/K), σ is the electrical conductivity (S/m), λ is the thermal conductivity (W/mK), and T is the absolute temperature (K). The main objective of this work was to obtain SnSe films via magnetron sputtering of a single target. Instead of common radiofrequency (RF) magnetron sputtering with a high voltage alternating current (AC) power source, a modified direct current (DC) power supply was employed. This technique in the classical version is not suitable for sputtering targets with relatively low thermal and electrical conductivity, such as SnSe. The proposed solution enabled stable sputtering of this target without detrimental cracking and arcing and resulted in high-quality polycrystalline SnSe films with unprecedented high values of ZT equal to 0.5 at a relatively low temperature of 530 K. All parameters included in ZT were measured in one setup, i.e., Linseis Thin Film Analyzer (TFA). The SnSe films were deposited at sputtering powers of 120, 140, and 170 W. They had the same orthorhombic structure, as determined by X-ray diffraction (XRD), but the thickness and microstructure examined by scanning electron microscopy (SEM) were dependent on the sputtering power. It was demonstrated that thermoelectric efficiency improved with increasing sputtering power and stable values were attained after two heating–cooling cycles. This research additionally provides further insights into the DC sputtering process and opens up new possibilities for magnetron sputtering technology.

Optimizing thermoelectric power factor in magnetron sputtered Cu 2 Se thin films by varying substrate temperature and synergy of Cu/Se ratio

Optimization of Thermoelectric Properties and Physical Mechanisms of Cu2Se-Based Thin Films via Heat Treatment

Thermoelectric Properties of Cu2Se Nano-Thin Film by Magnetron Sputtering

High Thermoelectric Performance of Cu 3 SbSe 4 Obtained by Synergistic Modulation of Power Factor and Thermal Conductivity

Enhanced Thermoelectric Performance of Cu2Se Alloys by Simultaneous Engineering of Thermal and Electrical Transport Properties Through S and Te co‐doping

Enhanced thermoelectric performance of Cu2Se thin film derived from potential barrier scattering by incorporating SnSe nano-dispersions

Thermoelectric Performance Enhancement of Cu2S by Se Doping Leading to a Simultaneous Power Factor Increase and Thermal Conductivity Reduction

Influence of Cu content on the phase composition and thermoelectric properties of deposited Cu-Se films

Influence of Sputtering Power on the Properties of Magnetron Sputtered Tin Selenide Films

Optimizing the thermoelectric properties of flexible Bi[math]Sb[math]Te[math] thin films via modulating magnetron sputtering power

Thermoelectric performance of copper-rich β-Cu2Se films with Ag-doping by magnetron sputtering

Ultrahigh thermoelectric performance in Cu2−ySe0.5S0.5 liquid-like materials

Achieving high thermoelectric performance through carrier concentration optimization and energy filtering in Cu3SbSe4-based materials

Enhanced Thermoelectric Performance and Service Stability of Cu2Se Via Tailoring Chemical Compositions at Multiple Atomic Positions

Largely enhanced performance of Cu 2 Se film by doping sulfur for flexible thermoelectric generators

High-performance thermoelectric properties of Cu 2 Se fabricated via cold sintering process

Characterization of Magnetron Sputtered BiTe-Based Thermoelectric Thin Films

Enhanced Thermoelectric Properties of Cu2SnSe3-Based Materials with Ag2Se Addition

Enhanced Thermoelectricity in High-Temperature Β-Phase Copper(I) Selenides Embedded with Cu2Te Nanoclusters.

Thermoelectric Performance of Surface-Engineered Cu 1.5- x Te-Cu 2 Se Nanocomposites

Thermoelectric Performance Enhancement of Eco-Friendly Cu2Se Through Incorporating CB4