Abstract:Miniaturization and low power consumption are critically important for development of wearable and mobile medical devices. The paper proposed a single-chip solution for acquisition of reflectance photoplethysmography (PPG), which can be used to measure heart rate and blood oxygen saturation for daily healthy monitoring and has less limitations on detection positions compared to transmittance PPG. In addition to a self-made photoelectric sensor and a LED driving circuit, the module is primarily based on MSP430FG4616 microcontroller minimum system, which incorporates the configurable trans-impedance amplifiers, high-performance 12-bit analog-to-digital conversion (ADC), dual 12-bit digital-to-analog conversions (DAC), 16-bit timers and 16-bit hardware multiplier. The integrated hardware provides the excellent performance on the pre-stage amplification of extremely small signal from photodiode as well as on generation of both analog and digital output of PPG signal. Moreover, functions of timing control, gain adaption, signal conditioning and analysis were also realized effectively via programming by the processor. The module with size of 2.5*2.5*0.5 cm (L*W*H) has been implemented and tested. With the power supply of 3V, it consumes no more than 2 mu A current under standby mode and 0.56 mA under normal working condition with PPG signal-noise-ratio (SNR) above 26 dB. The total power consumption is 1.68 mW under normal working condition, which is much lower than most of the existing commercial products. Based on it, the more miniaturized module with size of 1.0*1.0*0.5 (L*W*H) has been designed and is in debug phase. In conclusion, the single-chip miniaturization solution in this paper could provide a feasible approach for PPG-based wearable or mobile medical devices.

A Low-Power High-Sensitivity Photocurrent Sensory Circuit with Capacitive Feedback Transimpedance for Photoplethysmography Sensing

A Low-Power High-Sensitivity Analog Front-End for PPG Sensor

14.85 Μw Analog Front-End for Photoplethysmography Acquisition with 142-Dbω Gain and 64.2-Parms Noise

An Integrated High-Gain Wide–Dynamic Range Photoplethysmography Sensor for Cardiac Health Monitoring

A Fully Integrated High-Sensitivity Wide Dynamic Range PPG Sensor with an Integrated Photodiode and an Automatic Dimming Control LED Driver

Low-Power High-Sensitivity Photoplethysmography Sensor for Wearable Health Monitoring System

A 2.1/5.2-NEF/PEF Capacitively Coupled Instrumentation Amplifier with Fast - Settling for Biosensor

A 2.3-5.7μW Tri-Modal Self-Adaptive Photoplethysmography Sensor Interface IC for Heart Rate, SpO2, and Pulse Transit Time Co-Monitoring

A 140-Db Dynamic Range Digital PPG Front-end IC with an Integrated MoSe2 Photodiode for Wearable Non-invasive Pulse Oximetry

A Fully Differential PPG Readout Amplifier with a Reconfigurable Bandwidth for Power Minimization

A 2.6 μW Monolithic CMOS Photoplethysmographic (PPG) Sensor Operating With 2 μW LED Power for Continuous Health Monitoring

A Miniaturized Single-Chip Oximetry Module Utilizing Reflectance Photoplethysmography

An Organic Electrochemical Transistor Integrated Photodetector for High Quality Photoplethysmogram Signal Acquisition

A 280 μW, 108 dB DR PPG-Readout IC With Reconfigurable, 2nd-Order, Incremental ΔΣM Front-End for Direct Light-to-Digital Conversion

A 1.8V 16μA 136.5dB DR PPG/NIRS Recording IC using Noise Shaping Triple Slope Light to Digital Converter

Ultra-High Input Impedance, Low Noise Integrated Amplifier for Noncontact Biopotential Sensing

A 136-GΩ Input-Impedance Active Electrode for Non-Contact Biopotential Signals Monitoring

A Sparse Sampling Sensor Front-end IC for Low Power Continuous SpO$_2$ \& HR Monitoring

A Hybrid Photoplethysmography (PPG) Sensor System Design for Heart Rate Monitoring

Multichannel Reflective PPG Earpiece Sensor with Passive Motion Cancellation

Organic Photoplethysmography Sensor Based on Directional Emission Microcavity Organic Light‐Emitting Device