Abstract:The microstructures and mechanical properties of a γ'-strengthened nickel-based superalloy, GH4099, produced by laser powder bed fusion, at room temperature and 900 °C are investigated, followed by three various heat treatments. The as-built (AB) alloy consists of cellular/dendrite substructures within columnar grains aligning in <100> crystal orientation. No γ' phase is observed in the AB sample due to the relatively low content of Al +Ti. Following the standard solid solution treatment, the molten pool boundaries and cellular/dendrite substructures disappear, whilst the columnar grains remain. The transformation of columnar grains to equiaxed grains occurs through the primary solid solution treatment due to the recovery and recrystallization process. After aging at 850 °C for 480 min, the carbides in the three samples distributed at grain boundaries and within grains and the spherical γ' phase whose size is about 43 nm ± 16 nm develop in the standard solid solution + aging and primary solid solution + aging samples (SA and PA samples) while the bimodal size of cubic (181 nm ± 85 nm) and spherical (43 nm ± 16 nm) γ' precipitates is presented in the primary solid solution + secondary solid solution + aging sample (PSA samples). The uniaxial tensile tests are carried out at room temperature (RT) and 900 °C. The AB sample has the best RT ductility (~51% of elongation and ~67% of area reduction). Following the three heat treatments, the samples all acquire excellent RT tensile properties (>750 MPa of yield strengths and >32% of elongations). However, clear ductility dips and intergranular fracture modes occur during the 900 °C tensile tests, which could be related to carbide distribution and a change in the deformation mechanism.

High-Temperature Steam Oxidation Behavior of VDM Alloy 699 XA Produced by Laser Powder Bed Fusion

Thermal Oxidation Behaviour of Ti6Al7Nb and Ti6Al4V Alloys

High-temperature Oxidation Behavior of AlCoCrCuFeNi High-Entropy Alloy by Selective Laser Melting

High-temperature oxidation behaviour of high chromium superalloys additively manufactured by conventional or extreme high-speed laser metal deposition

High Temperature Oxidation Performance of an Additively Manufactured Mo–9Si–8B Alloy

The anisotropic oxidation behavior of Hastelloy X alloy fabricated by laser powder-bed fusion (LPBF) during the cyclic oxidation process

High Temperature Oxidation Behavior of an Equimolar Cr-Mn-Fe-Co High-Entropy Alloy

Effect Of Steam Temperature On Oxidation Behavior Of Gh2984 Alloy As A Candidate For 700 Degrees C Advanced Ultra-Supercritical Boilers

The high temperature oxidation behavior of a superalloy prepared by vacuum induction melting and electron beam smelting: A comparative study

High-temperature steam oxidation experiment of molten zirconium alloy

Oxidation behaviour and microstructural stability of alloy 625 during long-term exposure in steam

Alloy Design for Additive Manufacturing: Early-Stage Oxidation of Nickel-Based Superalloys

Oxidation and Hot Corrosion Behaviors of Service-Exposed and Heat-Treated Gas Turbine Vanes Made of IN939 Alloy

High-Temperature Oxidation Kinetics and Behavior of Ti–6Al–4V Alloy

The oxidation behavior of the CrFeCoNiAlx (x = 0, 1.0, and 5.0 wt%) high-entropy alloy synthesized with Al elemental powder via powder bed fusion technique at high temperatures

Oxidation behavior of lightweight Al2NbTi3V2Zr high entropy alloy at 1000°C

Oxidation behavior of high Hf nickel-based superalloy in air at 900, 1000 and 1100°C

Oxidation Behavior and Breakdown of an Aluminide Coating on DZ40M Alloy at High Temperatures

Oxidation kinetic behavior and microstructure mechanism of GH3536 alloy fabricated by laser powder bed fusion

Influence of Various Heat Treatments on Microstructures and Mechanical Properties of GH4099 Superalloy Produced by Laser Powder Bed Fusion

Cyclic oxidation and hot corrosion performance of direct metal laser sintered and wrought alloy 718 at 800°C in air and molten salts containing Na2SO4, V2O5 and NaCl