Abstract:Objective: The present study determined the influence of polymerization shrinkage of eight commercially available hybrid, micro-filled and nano composites (Z100 and Filtek Supreme, 3M-ESPE; Charisma and Durafill, Heraeus Kulzer; Tetric and InTen-S, Ivoclar Vivadent; Enamel plus HFO, GDF; Palfique Estelite Low Flow, Tokuyama) placed in large class 1 cavities on the bond strength to dentin. Methods: Polymerization shrinkage was recorded for 300 s at room temperature with a Stress-Strain-Analyzer (C(FACTOR)=0.3). The maximum contraction stresses after 300 s, the time until gelation (t(0.5 N)) and the coefficient of near linear fit of contraction force/time (gradient) were analysed. For the evaluation of the micro-tensile-bond-strength (micro-TBS), hourglass shape samples obtained from a total of 32 no carious extracted human third and second molars, randomly divided into 8 groups, were used. Micro tensile bond strengths were determined by computing the ratio of maximum load by the adhesion area of the hourglass shape. In order to analyze the quality of the polymerization within fillings, hardness profiles of a surface cut thought the middle of the restored tooth and along the tooth axis were made. Further, the modulus of elasticity, determined in a three-point-bending test, as well as the variation of the modulus of elasticity and of the hardness within a filling were considered. The statistical analyses were conducted by ANOVA (alpha=0.05) and post-hoc Tukey's test. Results: A significant correlation between polymerization shrinkage and micro-TBS was found (Pearson; -0.44). The correlation between modulus of elasticity in bending test and shrinkage stress (Pearson; 0.77), coefficient of near linear fit m (Pearson; 0.72), time until gelation (Pearson; -0.52) and micro-tensile-bond-strength (Pearson; -0.45) was also significant. A high polymerization tension and modulus of elasticity negatively affected the adhesion of the composite to the tooth hard substance. Further, the number of samples lost during the slice cutting and the hourglass shape preparation was found to correlate highly significantly with the shrinkage stress (Pearson; 0.97), coefficient of near linear fit m (Pearson; 0.94) and modulus of elasticity (Pearson; 0.82). All materials showed sufficient polymerization within the filling in comparison to the filling surface, the hardness at the bottom of the filling was greater than 80% of the maximum hardness value. The modulus of elasticity was not considerably reduced within the filling. Significance: High contraction stress and modulus of elasticity, fast development of contraction force and an early start of stress build-up of materials placed in restrictive cavities cause tension in the material with a possible subsequent distortion of the bond to the tooth structure. A low modulus of elasticity is not necessarily associated with high bond strength. However, it causes a more uniform stress distribution at the restorative composite-tooth interface. This is also evident in a reduced sample loss during the different stages of sample preparation.

Polymerization shrinkage stress of contemporary dental composites: Comparison of two measurement methods

Polymerization shrinkage of contemporary dental resin composites: Comparison of three measurement methods with correlation analysis

Evaluation of micro-tensile bond strengths of composite materials in comparison to their polymerization shrinkage

Determination of polymerization shrinkage stress of universal hybrid composite resins by photo-elastic stress analysis

Assessments of polymerization shrinkage by optical coherence tomography-based digital image correlation analysis-Part II: Effects of restorative composites

Contraction stress of low-shrinkage composite materials assessed with different testing systems

Polymerization shrinkage and stress analysis during dental restoration observed by digital image correlation method

3D micro-CT and O-PTIR spectroscopy bring new understanding of the influence of filler content in dental resin composites

Finite Element Stress Analysis of Three Filling Techniques for Class V Light-cured Composite Restorations

Emerging technologies for the evaluation of spatio-temporal polymerisation changes in flowable vs. sculptable dental resin-based composites

Comparision of polymerization shrinkage of ten kinds of nanofilled light-cured composite resin

Evaluation of Two Resin Composites Having Different Matrix Compositions

Polymerization characteristics, flexural modulus and microleakage evaluation of silorane-based and methacrylate-based composites.

Monomer conversion, microhardness, internal marginal adaptation, and shrinkage stress of bulk-fill resin composites

Shrinkage stress and elastic modulus assessment of bulk-fill composites

Compression Behavior of Dental Flowable Composites—Digital Image Correlation and Numerical Analysis

Polymerization Shrinkage Kinetics and Degree of Conversion of Resin Composites.

Release of contraction stress of dental resin composites by water sorption

Characterization of dental light-curing resin composites incorporating multiple modified low-shrink monomers

Evaluation of depth-wise post-gel polymerisation shrinkage behaviour of flowable dental composites

Development and application of a new testing system of contraction stress of composite materials