Abstract:Objective: The present study determined the influence of polymerization shrinkage of eight commercially available hybrid, micro-filled and nano composites (Z100 and Filtek Supreme, 3M-ESPE; Charisma and Durafill, Heraeus Kulzer; Tetric and InTen-S, Ivoclar Vivadent; Enamel plus HFO, GDF; Palfique Estelite Low Flow, Tokuyama) placed in large class 1 cavities on the bond strength to dentin. Methods: Polymerization shrinkage was recorded for 300 s at room temperature with a Stress-Strain-Analyzer (C(FACTOR)=0.3). The maximum contraction stresses after 300 s, the time until gelation (t(0.5 N)) and the coefficient of near linear fit of contraction force/time (gradient) were analysed. For the evaluation of the micro-tensile-bond-strength (micro-TBS), hourglass shape samples obtained from a total of 32 no carious extracted human third and second molars, randomly divided into 8 groups, were used. Micro tensile bond strengths were determined by computing the ratio of maximum load by the adhesion area of the hourglass shape. In order to analyze the quality of the polymerization within fillings, hardness profiles of a surface cut thought the middle of the restored tooth and along the tooth axis were made. Further, the modulus of elasticity, determined in a three-point-bending test, as well as the variation of the modulus of elasticity and of the hardness within a filling were considered. The statistical analyses were conducted by ANOVA (alpha=0.05) and post-hoc Tukey's test. Results: A significant correlation between polymerization shrinkage and micro-TBS was found (Pearson; -0.44). The correlation between modulus of elasticity in bending test and shrinkage stress (Pearson; 0.77), coefficient of near linear fit m (Pearson; 0.72), time until gelation (Pearson; -0.52) and micro-tensile-bond-strength (Pearson; -0.45) was also significant. A high polymerization tension and modulus of elasticity negatively affected the adhesion of the composite to the tooth hard substance. Further, the number of samples lost during the slice cutting and the hourglass shape preparation was found to correlate highly significantly with the shrinkage stress (Pearson; 0.97), coefficient of near linear fit m (Pearson; 0.94) and modulus of elasticity (Pearson; 0.82). All materials showed sufficient polymerization within the filling in comparison to the filling surface, the hardness at the bottom of the filling was greater than 80% of the maximum hardness value. The modulus of elasticity was not considerably reduced within the filling. Significance: High contraction stress and modulus of elasticity, fast development of contraction force and an early start of stress build-up of materials placed in restrictive cavities cause tension in the material with a possible subsequent distortion of the bond to the tooth structure. A low modulus of elasticity is not necessarily associated with high bond strength. However, it causes a more uniform stress distribution at the restorative composite-tooth interface. This is also evident in a reduced sample loss during the different stages of sample preparation.

Polymerization characteristics, flexural modulus and microleakage evaluation of silorane-based and methacrylate-based composites.

Comparison between a silorane-based composite and methacrylate-based composites: shrinkage characteristics, thermal properties, gel point and vitrification point.

Characterization of dental light-curing resin composites incorporating multiple modified low-shrink monomers

[Aging of Silorane- and Methacrylate-Based Composite Resins: Effects on Color and Translucency].

Evaluation of micro-tensile bond strengths of composite materials in comparison to their polymerization shrinkage

A Review of Silorane and Methacrylate Based Composites and Effective Factors on Microleakage of them

Development and application of a new testing system of contraction stress of composite materials

Polymerization shrinkage of contemporary dental resin composites: Comparison of three measurement methods with correlation analysis

Marginal integrity of low-shrinkage and methacrylate-based composite resins: Effect of three different hemostatic agents

Monomer conversion, microhardness, internal marginal adaptation, and shrinkage stress of bulk-fill resin composites

Polymerization shrinkage stress of contemporary dental composites: Comparison of two measurement methods

Contraction stress of low-shrinkage composite materials assessed with different testing systems

Comparative evaluation of sealing ability of two self-adhesive flowable composites following various restorative techniques in Class V lesions: An in vitro study

Characterization of Contemporary Conventional, Bulk-fill, and Self-adhesive Resin Composite Materials

Class II composite resin restorations with two polymerization techniques: relationship between microtensile bond strength and marginal leakage

Adhesiveness of Dental Resin-Based Restorative Materials Investigated with Atomic Force Microscopy

Evaluation of Microvoid and Microleakage Potential of Bulk-Fill Resin Composites in MOD Restorations

Synthesis of none Bisphenol A structure dimethacrylate monomer and characterization for dental composite applications

Retentive strength and marginal discrepancies of a ceramic-reinforced calcium phosphate luting agent: An in vitro pilot study

Experimental Study of Compomer Sealant with Non-Rinse Conditioner Used on Permanent Molar

Evaluation of Two Resin Composites Having Different Matrix Compositions