Abstract:Objectives: Resin-based composites (RBCs) are commonly used in dental restorations. It is known that RBCs undergo volumetric shrinkage during photo-polymerization leading to a detrimental increased stress state at the RBC-tooth interface and potentially early restoration failure. The objectives of this in vitro study were: (1) to ascertain whether shrinkage strain could be measured using in-fibre Bragg grating (FBG) technology, without confounding effects of temperature; and (2) to ascertain whether FBGs can detect alteration in shrinkage strain with introduction of a surface condition change at the RBC-cavity analog interface. Methods: Aluminum cavity analogs with simulated cavity dimensions 3.5 mm height x 2 mm width x 8 mm length and 2 mm wall thickness were secured in a 3D printed experimental jig. Two FBGs were used in the RBC space, one that was covered with a polyimide tube and that measured only temperature, and another that was affected by both mechanical strain and temperature. Experiments to determine if the two FBG system could be used to compensate for thermal artefacts were contrived to verify that a tube-covered and bare FBG measure the same temperature effect (n = 5). In situ photo-polymerization experiments, which consisted of using controlled amounts of SureFil SDR Flow + RBC, were performed to study RBC shrinkage behavior. As-machined (n = 10) and micro-etched (n = 11) cavity analogs were used. Significant differences in FBG measurements, which could indicate the ability of FBGs to detect alterations in strain across surface preparations, were determined using one tail t-tests at 95% confidence. Finally, additional temperature experiments were conducted 5 h after initial light exposure using the same light irradiation regiment to investigate temperature effects within a cured RBC system (n = 3). Results: For temperature measurement, the tubing-covered and bare FBGs measured temperature changes with time-lag of 3.7 ± 1.4 s (tubing-covered FBG relative to bare). For measurements in cured RBC, the bare FBG and tubing-covered FBG measured different strains, with the bare FBG measuring larger apparent strains because this FBG is affected by thermal volumetric expansion of the RBC and a temperature increase of the FBG itself. The tubing covered FBG, that is isolated from volumetric expansion effects, measured relatively less. The interpretation of these results is that thermally-compensated strain measures (in-situ) could require simultaneous use of two FBGs (one strain isolated). In situ measurements of the photo-polymerization procedure for as-machined analogs at two time-points, 500 and 1000 s, were determined to be -485.43 ± 131.06 μstrain and -524.96 ± 134.78 μstrain, respectively. For air-abraded surfaces measures were significantly lower at (p < 0.001) -211.36 ± 12.38 μstrain and -228.07 ± 49.08 μstrain, respectively. Conclusions: To measure shrinkage strain and compensate for associated thermal effects from photo-polymerization, systems employing two FBGs, one of them isolated from thermal volumetric expansion, may be required. The presented approach proved capable of detecting significant alteration in strain across two surface preparations.

Evaluation of depth-wise post-gel polymerisation shrinkage behaviour of flowable dental composites

Polymerization shrinkage of contemporary dental resin composites: Comparison of three measurement methods with correlation analysis

Emerging technologies for the evaluation of spatio-temporal polymerisation changes in flowable vs. sculptable dental resin-based composites

Assessments of polymerization shrinkage by optical coherence tomography-based digital image correlation analysis-Part II: Effects of restorative composites

3D micro-CT and O-PTIR spectroscopy bring new understanding of the influence of filler content in dental resin composites

Monomer conversion, microhardness, internal marginal adaptation, and shrinkage stress of bulk-fill resin composites

In situ measurement of dental resin-based composite volumetric shrinkage and temperature effects using in-fibre bragg grating methods

Physicomechanical properties and polymerization shrinkage of the newly developed radiopaque flowable composite derived from rice husk

Post-curing in dental resin-based composites

Evaluation of Two Resin Composites Having Different Matrix Compositions

Polymerization Shrinkage Kinetics and Degree of Conversion of Resin Composites.

Evaluation of micro-tensile bond strengths of composite materials in comparison to their polymerization shrinkage

Finite Element Stress Analysis of Three Filling Techniques for Class V Light-cured Composite Restorations

Polymerization shrinkage stress of contemporary dental composites: Comparison of two measurement methods

Effect of High-radiant Emittance and Short Curing Time on Polymerization Shrinkage Vectors of Bulk Fill Composites

Comparison of polymerization shrinkage of a new bulk-fill flowable composite with other composites: An in vitro study

Physico-mechanical characteristics of commercially available bulk-fill composites

[Evaluation of Laser Triangulation Method for Measurement of Post-Gel Shrinkage and Post-Vitrification Shrinkage in Composite Resins].

Mechanical properties and fracture behavior of flowable fiber reinforced composite restorations

Study on the Polymerization Shrinkage and Mechanical-Physical Properties of Dental Resin Composite Modified by Polyurethane Dimechacrylate and Glass Flake Fillers

Comparative analysis of self-cure and dual cure-dental composites on their physico-mechanical behaviour