Abstract:The structural stability of engineering rock mass under dynamic disturbance is directly associated with the fracture mechanics properties in engineering practice. Fully understanding the rock’s fracture mechanical behavior and crack evolution caused by stress concentration at the crack tip in engineering rock mass under dynamic load can offer useful insight into the rock’s dynamic fracture mechanism. A dynamic test using split-Hopkinson pressure bar (SHPB) test system was performed on a single prefabricated fissure sandstone centrally cracked Brazilian disk (CCBD) specimens. Based on the theory of fracture mechanics and one-dimensional stress wave theory, the dynamic crack initiation criterion of CCBD specimen is proposed, and the regression model of sandstone’s dynamic fracture toughness under the coupling effect of fissure angle and strain rate is established by using response surface methodology (RSM). The influence of strain rate and fissure angle on stress wave characteristics, dynamic tensile mechanical behavior, and fracture mechanics characteristic was investigated in this study. The findings demonstrate that: (1) The fissure angle plays a pivotal role in determining the failure mode of sandstone. As the fissure angle increases, three distinct failure modes emerge in the sandstone specimens, while variations in strain rate have minimal impact on the fracture mode of these specimens. (2) Alterations in the fissure angle result in changes to the waveform of transmitted waves. When the fissure angle is below 30°, the transmitted wave exhibits “double peak” characteristics; when it exceeds 30°, a “single peak” waveform is observed. This phenomenon can be attributed to diffraction principles governing incident waves. (3) When the impact pressure is 0.2 MPa, the peak load initially exhibits an increase followed by a decrease, with the peak load reaching its maximum at a fracture angle of 60°; when the impact pressures are 0.3 and 0.5 MPa, there exists a negative correlation between the peak load and the fissure angle. (4) The influence of strain rate on sandstone’s fracture resistance is predominant, with alterations in fissure angle exerting an auxiliary effect on this property. The research results can provide a theoretical and experimental basis for dynamic disaster prevention in urban underground space.

Investigation on Fracture Mode and Initiation Mechanisms of Cracks in Sandstone Disk Containing a Preexisting Flaw

Failure and Mechanical Behaviors of Sandstone Containing a Pre-existing Flaw Under Compressive–shear Loads: Insight from a Digital Image Correlation (DIC) Analysis

Experimental and DEM study on failure behavior and stress distribution of flawed sandstone specimens under uniaxial compression

Cracking Behavior and Acoustic Emission Characteristics of Rock Containing a Single Preexisting Flaw

Experimental study of the effect of crack distribution on the failure mechanism of sandstone specimens based on inclination angles and number of parallel flaws

Fracture behavior of cylindrical sandstone specimens with two pre-existing flaws: experimental investigation and PFC3D simulation

Failure Behavior of Sandstone Specimens Containing a Single Flaw Under True Triaxial Compression

Systematic detection and evaluation of cracking behavior of flawed brittle sandstones with AE and 3D-DIC techniques

Quantitative investigation of the cracking mechanism of 3D sand-printed rock containing a fold flaw

Crack Propagation and Fragmentation Characteristics of Single-Flawed Sandstone Samples under Different Loading Conditions

Discrete element modeling on crack evolution behavior of sandstone containing two oval flaws under uniaxial compression

Experimental investigation on mechanical, acoustic, and fracture behaviors and the energy evolution of sandstone containing non-penetrating horizontal fissures

Deformation localization and crack propagation of sandstone containing different flaw inclination angles under different loading rates

Experimental Study on Dynamic Tensile Mechanical Behavior and Fracture Mechanical Characteristics of Sandstone with a Single Prefabricated Fissure

Numerical investigation on the influence of secondary flaw lengths on the mechanical characteristics and cracking behaviour of red sandstone containing orthogonal cross flaws

Cracking process and acoustic emission characteristics of sandstone with two parallel filled-flaws under biaxial compression

Numerical and Experimental Assessment of the Sandstone Fracture Mechanism by Non-uniform Bonded Particle Modeling

Investigation of the compression-shear fracture characteristics of flaw-filled sandstone under confining pressure

Failure characteristics of coarse and fine sandstone containing two parallel fissures subjected to true triaxial stresses

Dynamic mechanical behaviors of pre-fractured sandstone with noncoplanar and unparallel flaws

Experimental study on the mechanical properties and damage evolution of red sandstone containing a single ice-filled flaw under triaxial compression