Abstract:Herein, a boundary lubrication (BL) mechanism based on the carbon-based tribofilms formed via Ni(Cu)-catalytic dehydrogenation of hydrocarbon oils was queried by performing standard ball-on disk tribotests on magnetron-sputtered WN, Ni, and W-N-Ni coatings in the oil-starvation condition. The experimental results indicate that both the bare GCr15 steel substrate and the sputtered W-N-Ni/MoN-Cu coatings exhibited comparable fine antiwear performance with friction coefficients below 0.09; however, no clues regarding the formation of the effectiveness of the graphite-like tribofilms on the contact surfaces were found, no matter whether the tested coatings were composited in amorphous or nanocrystallized structures. An under-s tanding of the antiwear mechanism was achieved by conducting a nonequilibrium molecular dynamics (NEMD) simulation of the confined shearing process, taking 1-decene chains as a model of the poly-alpha-olefin 10 base oil. It was found that as the normal load increases from 0.14 to 9.2 GPa, the "sandwiched" sheared oil molecules undergo a liquid-to-solidlike phase transition at a threshold pressure of approximately 0.54 GPa, above which the solidified oil film responds as an elastic protective layer between rigid walls and provides lower friction coefficients and energy dissipation than those of laminar shear motion. The main reasons are the elastic compliance of solidlike oil molecules and the occurrence of boundary slippage on the liquid-wall interface. The comparison of NEMD simulation among confined sheared boundary films of nonhydrogenated diamond-like carbon (DLC), hydrogen-terminated DLC, laminar fluid layers, and solidified oil films further reveals that it is the flexibility of C-C backbones as well as the elastic compliance of terminal C-H bonds that play a dominant role in the low-friction behavior of solidlike oil films in oil-starvation lubrication. Moreover, the simulation results indicate that the temperature increment of the confined sheared 1-decene under 0.14-9.2 GPa loads is generally below 20 K, which is far below the active temperature of 1-decene's catalytic dehydrogenation and pyrolysis reaction. These results support that in a steady state BL with low friction coefficients at room temperature, the formation of lubricious tribofilms via catalytic dissociation of alkanes can hardly be triggered due to the limited temperature increment, even when the catalysts of Ni/Cu are composited in the sliding surfaces.

Understanding the Effect of Oil-Based Lubricants on the Tribological Behavior of Fe–Cr Alloys from Reactive Molecular Dynamics

Optimized Tribological Performance Deriving from Multiple Strengthening Effects of Fe–Ni–Mo–Cr Alloy

Influence of Nanoparticles in Lubricant on Sliding Contact of Atomic Rough Surfaces—A Molecular Dynamics Study

Friction reactions induced by selective hydrogenation of textured surface under lubricant conditions

Effect of lubricant additives on the tribological behavior of aluminum alloy against steel

Tribological Dependence of the High-Performance Ferrous-Based Coating on Different Coating Counterparts in Engine Oil

Tribological properties of AlCoCrFeNiCu high-entropy alloy in hydrogen peroxide solution and in oil lubricant

Elastic Lubricious Effect of Solidlike Boundary Films in Oil-Starvation Lubrication

Study on Lubrication Characteristics of C4-Alkane and Nanoparticle during Boundary Friction by Molecular Dynamics Simulation

Tribological Properties of Cr Coating Lubricated with Different Lubricants

Submicron-Lubricant Based on Crystallized Fe3O4 Spheres for Enhanced Tribology Performance

Understanding the Lubrication Mechanism Between the Polyhydroxyl Group Lubricants and Metal Surfaces

Friction dependence on the textured structure of an amorphous carbon surface: A reactive molecular dynamics study

Molecular Dynamics Simulation of the Effect of Nanoparticles on the Tribological Properties of Lubricant Film

Frictional behavior and tribo-carbonization of a synthetic engine oil (SJ/CF/5W-30) with different tribo-materials under stepwise heating conditions

An atomic insight into the stoichiometry effect on the tribological behaviors of CrCoNi medium-entropy alloy

How Polytetrafluoroethylene Lubricates Iron: An Atomistic View by Reactive Molecular Dynamics

Influence of Cr Addition on Tribological Properties of Bulk Fe2B under Dry Friction and Water Lubrication

Dispersion-tribological Property Relationship in Mineral Oils Containing 2D Layered Α-Zirconium Phosphate Nanoplatelets

Effects of a hierarchical pore structure on the tribological properties of an oil-containing iron-based composite

Experimental and Modelling Study of Friction Evolution and Lubricant Breakdown Behaviour under Varying Contact Conditions in Warm Aluminium Forming Processes