Abstract:Soil heat flux is an important component of the energy balance at the land surface. Heat flux plates have been used widely to measure soil heat flux, but suffer from errors such as heat flow distortion and soil-plate contact resistance. The Philip correction and self-calibrating heat flux plates have been applied to minimize measurement errors. The objectives of this study were to evaluate the effectiveness of heat flux plate correction methods and to introduce improved approaches for applying these methods under field conditions. Soil heat flux at a depth (z) below the surface (G(z)) was measured with conventional and self-calibrating plates buried at 2, 6, and 10 cm in a bare soil. Adjacent to the soil heat flux plates, soil thermal conductivity (lambda(s)) and temperature gradients were measured simultaneously with heat-pulse sensors, allowing Gz to be determined with the gradient method. The gradient method values were used as a standard to evaluate the performance of the heat flux plates. Temporal lambda(s) values were also estimated from soil sand content, bulk density and water content using a thermal conductivity model. At the 6- and 10-cm depths, the conventional plates underestimated G(z) by 4.3-10.2 Wm(-2) due to heat flow distortion errors resulting from a mismatch between lambda(s) and plate thermal conductivity (lambda(p). When the Philip correction was applied, both the measured and modeled lambda(s) values improved the accuracy of conventional heat flux plates. However, the modeling approach simplified the procedure for obtaining lambda(s). The self-calibrating plate effectively corrected G(z) errors associated with heat flow distortion (accurate to within 6.4W m(-2)) at the 6 cm and 10 cm depths. At the 2 cm depth, both types of plates produced erroneous Gos data, which were attributed to alterations in the thermal field and heat flux pattern around the plates due to blocking convective heat and water transfer. We also demonstrated that the heating process of the self-calibrating plate could bias G(z) data by disturbing the heat flow field around the plate. Voltage signals during and shortly after self-calibration should be discarded from data analysis. With these corrections, heat flux plates can provide an effective method for measuring soil heat flux. (C) 2015 Elsevier B.V. All rights reserved.

Correct Use of the Guarded-Hot-Plate Method for Thermal Conductivity Measurements on Solids

Design and Construction of a Guarded Hot Plate Apparatus Operating Down to Liquid Nitrogen Temperature.

Correct Use of the Transient Hot-Wire Technique for Thermal Conductivity Measurements on Solids

Investigation and Optimization of the Hot Disk Method for Thermal Conductivity Measurements up to 750 °C

INSTALLATION FOR DETERMINING THE THERMAL CONDUCTIVITY OF PLATES BY THE STATIONARY METHOD

Analysis and Improvement of the Hot Disk Transient Plane Source Method for Low Thermal Conductivity Materials

Long Short Hot-Probe Method for Determining Thermophysical Properties

A high-precision method to measure thermal conductivity of solids using reversible heat flux

Field Evaluation and Improvement of the Plate Method for Measuring Soil Heat Flux Density

Measurement Techniques for Thermal Conductivity and Interfacial Thermal Conductance of Bulk and Thin Film Materials

Novel, Cost Effective, and Reliable Method for Thermal Conductivity Measurement

Automatic Algorithm Applied for Calculating Thermal Conductivity by Transient Plane Source Method

Estimation of Soil and Grout Thermal Properties for Ground-Coupled Heat Pump Systems: Development and Application

A Method to Measure Heat Flux in Convection Using Gardon Gauge

Quantitative Measurement of Thermal Conductivity by SThM Technique: Measurements, Calibration Protocols and Uncertainty Evaluation

Analytical Investigation of the Limits for the In-Plane Thermal Conductivity Measurement Using a Suspended Membrane Setup

Measurement and identification of temperature-dependent thermal conductivity for thermal insulation materials under large temperature difference

Determination of the Convective Heat Transfer Coefficient in Three-Dimensional Inverse Heat Conduction Problems

Theoretical introduction to express way of the complex determination of the thermophysical parameters of metals

A Novel Portable Absolute Transient Hot-Wire Instrument for the Measurement of the Thermal Conductivity of Solids

The Principle To Measure Thermal Conductivity By A New Thermal Probe Method