Abstract:Inorganic CsPbIBr2 perovskite has been considered as a promising light-absorbing material for solar cells due to its high stability and suitable bandgap. Although the remarkable improvement of CsPbIBr2 PSC has been achieved, the efficiency of this cell is still lower than those of other analogues and far below its theoretical limit. This is mainly due to the serious charge recombination in the as-fabricated CsPbIBr2 cells derived from the poor-quality CsPbIBr2 perovskite film with a large quantity of defects and numerous grain boundaries. Therefore, fabricating high-quality CsPbIBr2 perovskite film is a key factor for the further efficiency improvement of CsPbIBr2 PSCs. Herein, phenylthiourea (PTU) additive is introduced into the CsPbIBr2 precursor to tailor the crystallization of CsPbIBr2 perovskite for fabricating high-quality CsPbIBr2 perovskite. The C=S group of PTU can coordinate with PbBr2 in the precursor owing to the lone-pair electrons on S and the empty orbits of Pb2+. The strong interaction between PTU and the CsPbIBr2 precursor components can form PTU·Pb···Br(I) intermediate phase in the precursor upon PTU introduction. The PTU·Pb···Br(I) intermediate phase can reduce the nucleation rate of perovskite and modulate the perovskite crystal growth because the extra energy is required to break the strong coordination bond in the intermediate phase, resulting in a low crystallization rate of CsPbIBr2 perovskite. Such a retardation of perovskite crystallization is conducive to the formation of high-crystallinity perovskite film with smooth surface, large crystal grains, high crystallization, and low density of defect. Meanwhile, the decomposition of PTU during thermal annealing makes the S2– inserted into interstitial of CsPbIBr2 crystal lattice, which greatly enhance the stability of CsPbIBr2 perovskite. The carbon-based PSCs with a normal n-i-p structure of FTO/compact-TiO2 layer/meso-TiO2 layer/perovskite film/carbon layer are fabricated, and their photovoltaic performances are measured under a simulated AM1.5 illumination (100 mW·cm–2). The PSC based on PTU-CsPbIBr2 perovskite delivers a high power conversion efficiency of 10.09%, which is much higher than that of the control device. This great improvement of photovoltaic performance can be attributed to the largely promoted perovskite quality, which enhances the charge collection and suppresses the charge recombination in the device. In addition, the unencapsulated device preserves 82% of the initial efficiency after being stored under ambient condition for 35 days, suggesting excellent stability. Therefore, this work provides an effective complementary strategy for effectively improving the performance of inorganic PSCs.

Enhancing efficiency and stability of perovskite solar cells through two-step deposition method with the addition of cesium halides to PbI2 precursor

Enhanced Crystallization and Optimized Morphology of Perovskite through Doping Indium-Based Metal-Organic Assembly: Achieving Significant Solar Cell Efficiency Enhancements

Efficient Perovskite Solar Cells Fabricated Through CsCl-Enhanced PbI2 Precursor Via Sequential Deposition.

Enhancing perovskite solar cells efficiency through cesium fluoride mediated surface lead iodide modulation

Simultaneous Incorporation of CsI in the Two‐step Deposition Process Boosts the Power Conversion Efficiency and Stability of Perovskite Solar Cells

Octylammonium Octyldithiocarbamate Assisted Modulation of Crystallization and Doping of In Situ‐Generated Lead Sulfide for Efficient and Highly Stable Carbon‐Based CsPbIBr2 Solar Cells

Tailoring of CsPbIBr2 Perovskite Crystallization Via Phenylthiourea for Stable and Efficiency Perovskite Solar Cells

Advances in cesium lead iodide perovskite solar cells: Processing science matters

Efficient and stable perovskite solar cells doped by cesium acetate

Highly Crystalline CsPbI2Br Films for Efficient Perovskite Solar Cells Via Compositional Engineering

Antisolvent‐Free Heterogenous Nucleation Enabled by Employing 4‐Tert‐Butyl Pyridine Additive and Two‐Step Annealing for Efficient CsPbI2Br Perovskite Solar Cells

High-Efficiency And Thermal/Moisture Stable Cspbi2.84br0.16 Inorganic Perovskite Solar Cells Enabled By A Multifunctional Cesium Trimethylacetate Organic Additive

High-performance carbon-based CsPbI2Br perovskite solar cells via small molecule modification

Achieving stable and high-efficiency (>21%) lead halide perovskite solar cells with δ-CsPbI2Br seed–assisted growth strategy

Mitigating interfacial and bulk defects via chlorine modulation for HTL-free all-inorganic CsPbI2Br carbon-based perovskite solar cells with efficiency over 14%

Crystallization Management of CsPbI2Br Perovskites by PbAc2-incorporated Twice Spin-Coating Process for Efficient and Stable CsPbI2Br Perovskite Solar Cells

Enhancement of thermal stability for perovskite solar cells through cesium doping

Phase transition induced recrystallization and low surface potential barrier leading to 10.91%-efficient CsPbBr3 perovskite solar cells

Cesium Acetate-Assisted Crystallization for High-Performance Inverted CsPbI3perovskite Solar Cells.

Bifunctional Lewis Base‐Assisted Fabrication of High‐Quality CsPbIBr2 Perovskite for Efficient and Stable Solar Cells

A double perovskite participation for promoting stability and performance of Carbon-Based CsPbI2Br perovskite solar cells