Abstract:Inorganic CsPbIBr2 perovskite has been considered as a promising light-absorbing material for solar cells due to its high stability and suitable bandgap. Although the remarkable improvement of CsPbIBr2 PSC has been achieved, the efficiency of this cell is still lower than those of other analogues and far below its theoretical limit. This is mainly due to the serious charge recombination in the as-fabricated CsPbIBr2 cells derived from the poor-quality CsPbIBr2 perovskite film with a large quantity of defects and numerous grain boundaries. Therefore, fabricating high-quality CsPbIBr2 perovskite film is a key factor for the further efficiency improvement of CsPbIBr2 PSCs. Herein, phenylthiourea (PTU) additive is introduced into the CsPbIBr2 precursor to tailor the crystallization of CsPbIBr2 perovskite for fabricating high-quality CsPbIBr2 perovskite. The C=S group of PTU can coordinate with PbBr2 in the precursor owing to the lone-pair electrons on S and the empty orbits of Pb2+. The strong interaction between PTU and the CsPbIBr2 precursor components can form PTU·Pb···Br(I) intermediate phase in the precursor upon PTU introduction. The PTU·Pb···Br(I) intermediate phase can reduce the nucleation rate of perovskite and modulate the perovskite crystal growth because the extra energy is required to break the strong coordination bond in the intermediate phase, resulting in a low crystallization rate of CsPbIBr2 perovskite. Such a retardation of perovskite crystallization is conducive to the formation of high-crystallinity perovskite film with smooth surface, large crystal grains, high crystallization, and low density of defect. Meanwhile, the decomposition of PTU during thermal annealing makes the S2– inserted into interstitial of CsPbIBr2 crystal lattice, which greatly enhance the stability of CsPbIBr2 perovskite. The carbon-based PSCs with a normal n-i-p structure of FTO/compact-TiO2 layer/meso-TiO2 layer/perovskite film/carbon layer are fabricated, and their photovoltaic performances are measured under a simulated AM1.5 illumination (100 mW·cm–2). The PSC based on PTU-CsPbIBr2 perovskite delivers a high power conversion efficiency of 10.09%, which is much higher than that of the control device. This great improvement of photovoltaic performance can be attributed to the largely promoted perovskite quality, which enhances the charge collection and suppresses the charge recombination in the device. In addition, the unencapsulated device preserves 82% of the initial efficiency after being stored under ambient condition for 35 days, suggesting excellent stability. Therefore, this work provides an effective complementary strategy for effectively improving the performance of inorganic PSCs.

Octylammonium Octyldithiocarbamate Assisted Modulation of Crystallization and Doping of In Situ‐Generated Lead Sulfide for Efficient and Highly Stable Carbon‐Based CsPbIBr2 Solar Cells

Enhanced Crystallization and Optimized Morphology of Perovskite through Doping Indium-Based Metal-Organic Assembly: Achieving Significant Solar Cell Efficiency Enhancements

Synergistic Effect of Surface p-Doping and Passivation Improves the Efficiency, Stability, and Reduces Lead Leakage in All-Inorganic CsPbIBr<sub>2</sub>-Based Perovskite Solar Cells

Bifunctional Lewis Base‐Assisted Fabrication of High‐Quality CsPbIBr2 Perovskite for Efficient and Stable Solar Cells

Tailoring of CsPbIBr2 Perovskite Crystallization Via Phenylthiourea for Stable and Efficiency Perovskite Solar Cells

Enhancing the Optical, Morphological and Electronic Properties of the Solution-Processed CsPbIBr2 Films by Li Doping for Efficient Carbon-Based Perovskite Solar Cells

Crystallization Management of CsPbI2Br Perovskites by PbAc2-incorporated Twice Spin-Coating Process for Efficient and Stable CsPbI2Br Perovskite Solar Cells

Antisolvent‐Free Heterogenous Nucleation Enabled by Employing 4‐Tert‐Butyl Pyridine Additive and Two‐Step Annealing for Efficient CsPbI2Br Perovskite Solar Cells

Promoted Charge Extraction in All-Inorganic CsPbBr3 Perovskite Solar Cells by a CsPbX3 (X = Br and I) Quantum Dot Interface Layer

Enhancing the Performance of Perovskite Solar Cells Through Cesium Halide Doping

Extrinsic Ion Distribution Induced Field Effect in CsPbIBr2 Perovskite Solar Cells.

Ionic Liquid Surface Treatment-Induced Crystal Growth of CsPbIBr2 Perovskite for High-Performance Solar Cells

Zirconium Doping to Enable High-Efficiency and Stable CsPbI2Br All-Inorganic Perovskite Solar Cells.

Suppressing Intrinsic Self-Doping Of Cspbibr(2)Films For High-Performance All-Inorganic, Carbon-Based Perovskite Solar Cells

Performance Enhancement of Hole Transport Layer-Free Carbon-Based CsPbIBr2 Solar Cells through the Application of Perovskite Quantum Dots

Promoting the Efficiency and Stability of CsPbIBr2-Based All-Inorganic Perovskite Solar Cells Through a Functional Cu2+ Doping Strategy.

Illumination Enhanced Crystallization and Defect Passivation for High Performance CsPbI3 Perovskite Solar Cells by Sacrificing Dye

Indium-Doped CsPbI2.5Br0.5 with a Tunable Band Structure and Improved Crystallinity for Thermo-Stable All-Inorganic Perovskite Solar Cells

Zinc and Acetate Co-doping for Stable Carbon-Based CsPbIBr2 Solar Cells with Efficiency over 10.6%

Boosting the Efficiency of Carbon-Based Planar CsPbBr3 Perovskite Solar Cells by a Modified Multistep Spin-Coating Technique and Interface Engineering

High-Efficiency (>14%) and Air-Stable Carbon-Based, All-Inorganic CsPbI2Br Perovskite Solar Cells Through a Top-Seeded Growth Strategy