Abstract:Corrigendum to: Jiehui Liu, Hongjun Hu, Yang Liu, Dingfei Zhang, Zhongwen Ou and Yan Zhi, "Mechanical properties and wear-corrosion resistance of a new compound extrusion process for magnesium alloy AZ61," Materials Testing , vol. 62, no. 4, pp. 395–399, 2020 (https://doi.org/10.3139/120.111476). As Figures 5a and c have already been published in other articles, the authors wish to replace them by the following figures: Worn surface morphology under load 5 N and reciprocating frequency 2 Hz of magnesium alloy made by a) CE process, b) DE process, c) friction coefficients varying with different loads of dry sliding. The authors would like to apologize for any inconvenience caused. © 2023 Walter de Gruyter GmbH, Berlin/Boston

Corrigendum to “Effects of preheating and carbon dilution on material characteristics of laser-cladded hypereutectoid rail steels”[Mater. Sci. Eng. A 712 (2018) 548–563 …

Corrigendum to “Effect of electropulsing on surface mechanical properties and microstructure of AISI 304 stainless steel during ultrasonic surface rolling process” [Mater. Sci. Eng. A 662 (2016) 456–467] (S0921509316303148) (10.1016/j.msea.2016.03.097))

Corrigendum for “A Novel Kinase Subverts Aluminium Resistance by Boosting Ornithine Decarboxylase‐dependent Putrescine Biosynthesis”

Erratum: Corrigendum to “High-fidelity micro-scale modeling of the thermo-visco-plastic behavior of carbon fiber polymer matrix composites” (Composite Structures (2015) 134 (132–141))

Corrigendum to “High-Fidelity Micro-Scale Modeling of the Thermo-Visco-plastic Behavior of Carbon Fiber Polymer Matrix Composites” [compos Struct 134 (2015) 132–141]

Corrigendum to: Mechanical properties and wear-corrosion resistance of a new compound extrusion process for magnesium alloy AZ61

Corrections to “zinc Oxide Nanostructures and High Electron Mobility Nanocomposite Thin Film Transistors” [nov 08 3001-3011

Corrigendum to "Effect of Sc contents on the mechanical properties and damping capacity of Al-Zn-Mg-Cu-Zr-Sc alloys with different grain structures" [Heliyon 10(2) January 2024 e24428]

Erratum to: Solid Particle Erosion Behaviour of Laser Sintered Heat Treated Ti–6Al–4V Alloy

Erratum to: Description of full-range strain hardening behavior of steels

Erratum: Thermal analysis of injectable, cellular scale optoelectronics with pulsed power (Proceedings of the Royal Society A: Mathematical, Physical and Engineering Sciences …

Erratum: Corrigendum: Printing, folding and assembly methods for forming 3D mesostructures in advanced materials

Corrigendum: Copper induced hollow carbon nanospheres by arc discharge method: controlled synthesis and formation mechanism (2016 Nanotechnology 27 335602)

Erratum to: Highly active zigzag-like Pt-Zn alloy nanowires with high-index facets for alcohol electrooxidation

Correction: Wu et al. 3D Thermal Network Supported by CF Felt for Improving the Thermal Performance of CF/C/Epoxy Composites. Polymers 2021, 13, 980

Corrigendum on “experimental study and thermodynamic modeling of a novel heat resistant explosive in different mono solvents”

Correction to: Milling-Related Brittle Fracture Mechanisms of a SiCp/Al Composite

Correction: Tang, L. et al., Effect of Oxygen Variation on High Cycle Fatigue Behavior of Ti-6Al-4V Titanium Alloy. Materials 2020, 13, 3858

Correction: Ultrahigh thermal conductive polymer composites by the 3D printing induced vertical alignment of carbon fiber

Correction To: Network-Strengthened Ti-6Al-4V/(TiC+TiB) Composites: Powder Metallurgy Processing and Enhanced Tensile Properties at Elevated Temperatures

Erratum To: Editorial