Abstract:This article has been retracted: please see Elsevier Policy on Article Withdrawal (http://www.elsevier.com/locate/withdrawalpolicy). This article has been retracted at the request of the Editor-in-Chief. The authors have reused figures and text that have already appeared in their previous articles. Figure 4a duplicates figure 3b of the article that had already appeared in the Journal of Alloys and Compounds 616 (2014) 173–183, http://dx.doi.org/10.1016/j.jallcom.2014.07.143, figure 5b (anticlockwise 90 degrees rotated and horizontally flipped) of the article that had appeared in Materials Characterization 98 (2014) 147–161, http://dx.doi.org/10.1016/j.matchar.2014.10.026, figure 6b of the article published by Surface & Coatings Technology 258 (2014) 467–484, http://dx.doi.org/10.1016/j.surfcoat.2014.08.052 and figure 8b (anticlockwise 90 degrees rotated and horizontally flipped) of the article published by the J. Mater. Sci.: Mater. Med. 26 (2015) 53. https://doi.org/10.1007/s10856-014-5371-5. The article also duplicates parts of the text that appeared in Materials Science & Engineering A 622 (2015) 1–6 http://dx.doi.org/10.1016/j.msea.2014.11.003. One of the conditions of submission of a paper for publication is that authors declare explicitly that their work is original and has not appeared in a publication elsewhere. Re-use of any data should be appropriately cited. As such this article represents an abuse of the scientific publishing system. The scientific community takes a very strong view on this matter and apologies are offered to readers of the journal that this was not detected during the submission process. Journal records indicate that confirmation of the submission and publication of the article was sent to the first author's email address, in addition to an email that used the corresponding author's name (tangguoyiforwork@163.com). The corresponding author and the first author wish to mention that the co-author Zion T.H. Tse was not involved in the preparation and handling of this article. He was not informed about the publication or granted the use of his name and affiliation in the publication. © 2019 Elsevier B.V.

Corrigendum to “Effect of electropulsing on surface mechanical properties and microstructure of AISI 304 stainless steel during ultrasonic surface rolling process” [Mater. Sci. Eng. A 662 (2016) 456–467] (S0921509316303148) (10.1016/j.msea.2016.03.097))

Corrigendum for “A Novel Kinase Subverts Aluminium Resistance by Boosting Ornithine Decarboxylase‐dependent Putrescine Biosynthesis”

Corrigendum to: Mechanical properties and wear-corrosion resistance of a new compound extrusion process for magnesium alloy AZ61

Corrigendum to “In situ synthesis of MgAlB4 whiskers as a promising reinforcement for aluminum matrix composites”[Mater. Sci. Eng. A 764 (2019) 138229]

Corrigendum to “quantitative Assessment of Structural and Compositional Colors Induced by Femtosecond Laser: A Case Study on 301LN Stainless Steel Surface” [appl. Surf. Sci. 484 (2019) 655–662]

Correction: Corrigendum: Autophagy-associated alpha-arrestin signaling is required for conidiogenous cell development in Magnaporthe oryzae

Corrigendum to "Effect of Sc contents on the mechanical properties and damping capacity of Al-Zn-Mg-Cu-Zr-Sc alloys with different grain structures" [Heliyon 10(2) January 2024 e24428]

Corrections to “zinc Oxide Nanostructures and High Electron Mobility Nanocomposite Thin Film Transistors” [nov 08 3001-3011

Corrigendum: Preparation and Characterization of 3D Porous Conductive Scaffolds with Magnetic Resonance Enhancement in Tissue Engineering (2019biomed. Mater.14 045013).

Retraction notice to: “Effect of electropulsing treatment on microstructure and mechanical properties of cold-rolled pure titanium strips” (Journal of Materials Processing Tech. (2015) 222 (27–32), (S0924013615000850), (10.1016/j.jmatprotec.2015.02.035))

Corrigendum to “surface Effect on the Contact Problem of a Piezoelectric Half-Plane” [int. J. Solids Struct, 185-186 (2020) 380–393]

Corrigendum to "Thiol-ene Michael-type formation of gelatin/poly(ethylene glycol) biomatrices for three-dimensional mesenchymal stromal/stem cell administration to cutaneous wounds" [Acta Biomater. 9(11) (2013) 8802-8814].

Retraction Note: Effect of Electropulsing Treatment on the Microstructure, Texture, and Mechanical Properties of Cold-Rolled Ti-6Al-4V Alloy

Retraction notice to “Influence of electropulsing treatment on microstructure and mechanical properties of Ti-6Al-4V alloy strip with lamellar microstructure” [Mater. Sci. Eng. A 622 (2015) 1−6](S0921509314013422)(10.1016/j.msea.2014.11.003)

Corrigendum to “synthesis and Characterization of Silica–acrylic–epoxy Hybrid Coatings on 430 Stainless Steel” [surface and Coatings Technology 204 (2009) 91–98]

Erratum To: Editorial

Erratum to: Highly active zigzag-like Pt-Zn alloy nanowires with high-index facets for alcohol electrooxidation

Erratum: Zhang, C. et al., The Effect of Substrate Biasing during DC Magnetron Sputtering on the Quality of VO2 Thin Films and Their Insulator–Metal Transition Behavior. Materials 2019, 12, 2160

Erratum To: Influence of Grain Refinement on the Corrosion Behavior of Metallic Materials: A Review

WITHDRAWN: Corrigendum to “sea Urchin-Like Aucore@Pdshell Electrocatalysts with High FAOR Performance: Coefficient of Lattice Strain and Electrochemical Surface Area” [applied Catalysis B: Environmental 260 (2020) 118200/Apcatb.2019.118200]

Erratum: Corrigendum: Printing, folding and assembly methods for forming 3D mesostructures in advanced materials