Abstract:This article has been retracted: please see Elsevier Policy on Article Withdrawal (http://www.elsevier.com/locate/withdrawalpolicy). This article has been retracted at the request of the Editor-in-Chief. The authors have reused figures and text that have already appeared in their previous articles. Figure 4a duplicates figure 3b of the article that had already appeared in the Journal of Alloys and Compounds 616 (2014) 173–183, http://dx.doi.org/10.1016/j.jallcom.2014.07.143, figure 5b (anticlockwise 90 degrees rotated and horizontally flipped) of the article that had appeared in Materials Characterization 98 (2014) 147–161, http://dx.doi.org/10.1016/j.matchar.2014.10.026, figure 6b of the article published by Surface & Coatings Technology 258 (2014) 467–484, http://dx.doi.org/10.1016/j.surfcoat.2014.08.052 and figure 8b (anticlockwise 90 degrees rotated and horizontally flipped) of the article published by the J. Mater. Sci.: Mater. Med. 26 (2015) 53. https://doi.org/10.1007/s10856-014-5371-5. The article also duplicates parts of the text that appeared in Materials Science & Engineering A 622 (2015) 1–6 http://dx.doi.org/10.1016/j.msea.2014.11.003. One of the conditions of submission of a paper for publication is that authors declare explicitly that their work is original and has not appeared in a publication elsewhere. Re-use of any data should be appropriately cited. As such this article represents an abuse of the scientific publishing system. The scientific community takes a very strong view on this matter and apologies are offered to readers of the journal that this was not detected during the submission process. Journal records indicate that confirmation of the submission and publication of the article was sent to the first author's email address, in addition to an email that used the corresponding author's name (tangguoyiforwork@163.com). The corresponding author and the first author wish to mention that the co-author Zion T.H. Tse was not involved in the preparation and handling of this article. He was not informed about the publication or granted the use of his name and affiliation in the publication. © 2019 Elsevier B.V.

Correction: Emokpaire et al. Effect of Ru on Deformation Mechanism and Microstructure Evolution of Single-Crystal Superalloys under Medium-Temperature and High-Stress Creep. Materials 2023, 16, 2732

Corrigendum to: Mechanical properties and wear-corrosion resistance of a new compound extrusion process for magnesium alloy AZ61

Correction: High-pressure structural phase transition and metallization in Ga2S3 under non-hydrostatic and hydrostatic conditions up to 36.4 GPa

Correction: Li et al. Recovery Behavior of the Macro-Cracks in Elevated Temperature-Damaged Concrete after Post-Fire Curing. Materials 2022, 15, 5673

Erratum to: Description of full-range strain hardening behavior of steels

Corrigendum to “Effect of electropulsing on surface mechanical properties and microstructure of AISI 304 stainless steel during ultrasonic surface rolling process” [Mater. Sci. Eng. A 662 (2016) 456–467] (S0921509316303148) (10.1016/j.msea.2016.03.097))

In Situ Observation of Phase Transformations of Pearlite Heat‐Resistant Steel during Solidification

On the effect of Ru upon creep behaviour and dislocation evolution in Ni-based single crystal superalloys

RETRACTED: Shi et al. Effect of Final Rolling Temperature on Microstructures and Mechanical Properties of AZ31 Alloy Sheets Prepared by Equal Channel Angular Rolling and Continuous Bending. Materials 2020, 13, 3346

Correction: Wang, F., et al. Effect of Low-Frequency Electromagnetic Casting on Micro-Structure and Macro-Segregation of 5A90 Alloy Ingots. Materials 2020, 13, 2720

Retracted: Mechanical Strength and Fatigue Fracture Analysis on Al-Zn-Mg Alloy with the Influence of Creep Aging Process

Corrigendum to "Effect of Sc contents on the mechanical properties and damping capacity of Al-Zn-Mg-Cu-Zr-Sc alloys with different grain structures" [Heliyon 10(2) January 2024 e24428]

Correction To: Effect of Y2O3 Addition on the Microstructure, Wear Resistance, and Corrosion Behavior of W-4.9Ni-2.1Fe Heavy Alloy

The Effect of Strain Rate on the Tensile Deformation Behavior of Single Crystal, Ni-Based Superalloys

Retraction notice to: “Effect of electropulsing treatment on microstructure and mechanical properties of cold-rolled pure titanium strips” (Journal of Materials Processing Tech. (2015) 222 (27–32), (S0924013615000850), (10.1016/j.jmatprotec.2015.02.035))

Publisher Correction: Transition from Source- to Stress-Controlled Plasticity in Nanotwinned Materials below a Softening Temperature

Correction: Zhang Et Al. the Stressing State Features of a Bottom Frame Structure Revealed from the Shaking Table Strain Data. Materials 2023, 16, 1809

Retraction notice to “Influence of electropulsing treatment on microstructure and mechanical properties of Ti-6Al-4V alloy strip with lamellar microstructure” [Mater. Sci. Eng. A 622 (2015) 1−6](S0921509314013422)(10.1016/j.msea.2014.11.003)

Correction: On the electronic structure and hydrogen evolution reaction activity of platinum group metal-based high-entropy-alloy nanoparticles

Effect of Stress on Microstructural Evolution and Mechanical Properties of 12cr3w3co Steel During Aging and Short-Term Creep

Effect of Rhenium and Ruthenium on the Deformation and Fracture Mechanism in Nickel-Based Model Single Crystal Superalloys During the In-Situ Tensile at Room Temperature