Correction: Wang, F., et al. Effect of Low-Frequency Electromagnetic Casting on Micro-Structure and Macro-Segregation of 5A90 Alloy Ingots. Materials 2020, 13, 2720

Fuyue Wang,Xiangjie Wang,Jianzhong Cui

DOI: https://doi.org/10.3390/ma14030572

2021-01-26

Abstract:In the original article [...].

What problem does this paper attempt to address?

Effect of Low-Frequency Electromagnetic Casting on Micro-Structure and Macro-Segregation of 5A90 Alloy Ingots

Fuyue Wang,Xiangjie Wang,Jianzhong Cui

DOI: https://doi.org/10.3390/ma13122720

2020-06-15

Abstract:The effect of low-frequency electromagnetic fields on the micro-structure and macro-segregation of 5A90 alloy ingots during the semi-continuous casting process were quantitatively investigated. The ingots of a 5A90 alloy with a diameter 170 mm were produced by the conventional direct chill casting (DCC) process and low-frequency electromagnetic casting (LFEC) with 10 Hz/100 A. The results showed that LFEC can substantially refine the micro-structure and shorten the width of the columnar grain area of an ingot. The refinement effect came with the relieving of grain boundary segregation and an improvement in the macro-segregation of the ingot. Compared with the traditional DCC process, the tensile properties of the aged alloy prepared by the LFEC process were improved due to the effects of the increase in solid solubility and the strengthening of the grain refinement, so that the stability of the tensile properties was also improved. Meanwhile, the rate of yield increased by 2.3% with a decrease in the peeling thickness of the ingot.
Microstructure and Tensile Properties of 5A90 Al–Mg–Li Alloy Containing Minor Sc Cast by Low-Frequency Electromagnetic Casting

Fuyue Wang,Yi Ren,Shuang Wang,Shuai Zhang,Hong Gao,Chengzhe Fu,Zherui Zhang,Jianzhong Cui

DOI: https://doi.org/10.1016/j.jmrt.2023.04.151

2023-01-01

Abstract:The effects of low-frequency electromagnetic casting (LFEC) on the microstructure and tensile properties of 5A90 Al-Mg-Li alloy with and without minor Sc were investigated. In addition to minor Sc, the refined microstructures of the conventional direct chill cast (DCC) alloy and the microstructures of the as-cast alloy were refined further and more equiaxed grains formed in LFEC ingots with Sc. Higher density, smaller size, and more uniform distribution Al3(Sc, Zr) in the aged alloy with Sc induced by LFEC, which pins on grain boundaries, can effectively inhibit recrystallization. As a result, it had been a significant improvement in strength which was mainly due to the Orowan effect of Al3(Sc, Zr) dispersoids combined with grain refinement. The ultimate tensile strength of 565.4 MPa, yield strength of 475.3 MPa, and the corresponding elongation of 6.4% were obtained in the asaged 5A90 alloy with 0.15 wt% Sc cast by LFEC at 10 Hz and 100 A.& COPY; 2023 The Authors. Published by Elsevier B.V.This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/4.0/).
Study on Micro-Structure, Solid Solubility and Tensile Properties of 5A90 Al–Li Alloy Cast by Low-Frequency Electromagnetic Casting Processing

Fuyue Wang,Ning Wang,Fang Yu,Xiangjie Wang,Jianzhong Cui

DOI: https://doi.org/10.1016/j.jallcom.2019.153318

IF: 6.2

2019-01-01

Journal of Alloys and Compounds

Abstract:In this paper, the low-frequency electromagnetic casting (LFEC) processing was introduced as an efficient pollution-free casting technique, and how it influenced the micro-structure and mechanical properties of 5A90 Al-Li alloy was investigated. The mechanical properties of the alloy had a close connection with the casting metallurgical quality and the precipitation phases. Compared to the conventional direct chill casting (DCC), the LFEC could promote the precipitate of the delta' (Al3Li)/beta' (Al3Zr) and reduce the width of PFZ, which enhanced the effect of the precipitation strengthen and alleviated the strain localization. Meanwhile, the micro-structure of the ingot was refined significantly and the metallurgical quality was improved after LFEC treatment due to the modification of the flow and temperature field of the sump that caused by the application of low-frequency electromagnetic field. Maximum yield strength and ultimate tensile strength of as-aged alloy cast by LFEC with 150 A/5 Hz could reach 371.85 MPa and 495.5 MPa, while elongation remained at 9.82%. (C) 2019 Elsevier B.V. All rights reserved.
Experimental Investigation of Microsegregation in Low Frequency Electromagnetic Casting of Al-4.5%Cu Binary Alloy

Dandan Chen,Haitao Zhang,Xiangjie Wang,Jianzhong Cui

DOI: https://doi.org/10.4028/www.scientific.net/amr.152-153.1217

2010-01-01

Advanced Materials Research

Abstract:Al-4.5%Cu ingots were prepared by a process of low frequency electromagnetic casting (LFEC) and conventional direct chill (DC) casting, respectively. The effects of low frequency electromagnetic field on the microsegregation were investigated from eutectic analysis and electro probe microanalysis (EPMA). It was found that the amount of the nonequilibrium eutectic and the dimension of the nonequilibrium eutectic were decreasing markedly. In contrast, the solute content in the α-Al phase increased to a certain extent in the presence of the low frequency electromagnetic field, and it increased with the incerasing electromagnetic.
Effect of Electromagnetic Field on Microstructure and Macrosegregation of Flat Ingot of 2524 Aluminium Alloy

Yu-bo Zuo,Jian-zhong Cui,Dan Mou,Qing-feng Zhu,Xiang-jie Wang,Lei Li

DOI: https://doi.org/10.1016/s1003-6326(14)63364-1

2014-01-01

Abstract:Low frequency electromagnetic casting (LFEC) process with the application of an induction coil outside the conventional direct chill (DC) casting mould was used to prepare the flat ingot of 2524 alloy and the effect of electromagnetic field on the microstructure and macrosegregation of this alloy was systematically studied. The results show that the flat ingot prepared by the LFEC process has a finer and more uniform as-cast microstructure and the grain morphology is transformed from dendrite and rosette-like to equiaxed structure. The LFEC process also shows a significant effect on macrosegregation, and with the application of electromagnetic field during casting process, the segregation in the centre of the ingot is obviously reduced. The mechanism of these effects was also discussed.
Effect of low-frequency electromagnetic field on microstructures and macrosegregation of ?270 mm DC ingots of an Al?Zn?Mg?Cu?Zr alloy

J DONG,J CUI,X ZENG,W DING

DOI: https://doi.org/10.1016/j.matlet.2005.01.009

IF: 3

2005-01-01

Materials Letters

Abstract:Compared with traditional direct chilling casting (DC) ingot, the edge and center microstructures of Φ270 mm low-frequency electromagnetic casting (LFEC) ingot are fine and uniform; and the macrosegregation is also greatly reduced. When the electromagnetic intensity is kept as 9000 At, with decreasing the frequency, the center microstructures are much finer and the macrosegregation is much lower. In the range of frequency employed in the experiments, the optimum frequency is found to be 15 Hz.
Effects of Low Frequency Electromagnetic Field on the Solidification Structure of Al-4.5%Cu Alloy During Level Casting Process

Xiangjie Wang,Dandan Chen,Huixue Jiang,Gaosong Wang,Qingfeng Zhu,Jianzhong Cui

DOI: https://doi.org/10.4028/www.scientific.net/amr.186.176

2011-01-01

Advanced Materials Research

Abstract:On the basis of conventional level casting, low frequency electromagnetic field is applied during conventional level casting process. Effects of low frequency electromagnetic field on melt flow, macrostructure and microstructure have been studied. The experiment is performed on the Al-4.5% Cu alloy, and the experimental results show that with the application of the low frequency electromagnetic field, the macrostructure and microstructure are changed greatly. The reasons for the low frequency electromagnetic field changing the macrostructure and microstructure of the ingot were summarized.
Effects of low-frequency electromagnetic field on microstructures and macrosegregation of continuous casting 7075 aluminum alloy

Beijiang Zhang,Jianzhong Cui,Guimin Lu

DOI: https://doi.org/10.1016/S0921-5093(03)00105-9

2003-01-01

Abstract:The influences of low-frequency electromagnetic field on microstructures and macrosegregation in continuous casting process were investigated experimentally. Ingot of 7075 aluminum alloy with a diameter of 200 mm was produced and as-cast structures were examined. In the presence of an electromagnetic field, a substantial reduction of grain size and the macrosegregation of alloying elements was achieved. Further, a pronounced evolution of microstructures and segregation with the frequency of electromagnetic field is presented. The results show that frequency plays a significant role in grain refinement and macrosegregation inhibition. A fine equiaxed as-cast structure is obtained when frequency reaches 15 Hz, while a proper frequency (30 Hz in this study) can inhibit the macrosegregation to the best effect.
Effect of Low Frequency Electromagnetic Field on Microstructures and Macro-Segregation of Direct Chill Casting Al-19.2%Si Alloys

Ke Qin,Jianzhong Cui

DOI: https://doi.org/10.4028/www.scientific.net/msf.546-549.953

2007-01-01

Abstract:The influences of low frequency electromagnetic field on microstructures and macro-segregation in direct chill casting process were investigated in the experiments, Al-19.2%Si alloys were semi-continuously cast into ingots with 100 mm in diameter. Microstructures and macrostructures of samples taken from different part of the cast with different electromagnetic field conditions were characterized by optical microscopy. The results showed that low frequency electromagnetic field refines the microstructures and reduces macro-segregation. Unlike casting without electromagnetic field, the primary Si grains were homogeneous with fine dimensions and the morphology of the primary silicon exhibited small blocky structures or near-spherical structures. Further more, decreasing frequency is beneficial to the improvement. In the range conditions in the experiments, the optimum frequency is found to be 15Hz. During casting, the temperature of the liquid metal in the sump was monitored. The results shown, under LFEC the width of the liquid-solid region became narrowed and the temperature field in the sump also became homogeneous.
Effect of Low Frequency Electromagnetic Casting on Microstructure and Properties of 4045 Alloy

QIN Ke,Jianzhong Cui

DOI: https://doi.org/10.3321/j.issn:1001-4977.2006.12.007

2006-01-01

Abstract:Under low frequency electromagnetic field,4045 alloys were semi-continuously cast into ingots with 100 mm in diameter.Microstructures of samples taken from different part of the cast with different cooling conditions were characterized by optical microscopy and scanning electron microscopy(SEM).Unlike casting without electromagnetic field,the α-Al dendrites were found to be thin and homogeneous under low frequency electromagnetic field.The eutectic Si grains are homogeneous with fine dimensions.Also,the Si-rich region formed at the edge of the ingot was found to be significantly decreased under low frequency electromagnetic field.The content of silicon in the primary aluminum reached to 2.59 %(wt).The mechanical properties of the electromagnetic modifying casting 4045 aluminum alloy improved with σb(ultimate tensile strength)of 225 MPa,ψ(elongation percentage)of 11.36% and HV(Vickers diamond hardness) of 69.5 MPa.
Correction: Chen et al. Evolution of Microstructure in Welding Heat-Affected Zone of G115 Steel with the Different Content of Boron. Materials 2022, 15, 2053.

Zhongyi Chen,Dongxu Kou,Zhengzong Chen,Fan Yang,Yonglin Ma,Yiming Li

DOI: https://doi.org/10.3390/ma17081731

2024-01-01

Abstract:In the original publication [...].
Effect of Low-Frequency Magnetic Field on Microstructures and Macro Segregation of Horizontal Direct Chill Casting 7075 Aluminum Alloy

Zhihao Zhao,Jianzhong Cui,Jie Dong,Beijiang Zhang

DOI: https://doi.org/10.1016/j.jmatprotec.2006.07.029

IF: 6.3

2007-01-01

Journal of Materials Processing Technology

Abstract:The horizontal direct chill (HDC) casting process is a well-established production route for an aluminum alloy ingot; however, the ingot may suffer from inhomogeneous microstructures and serious macrosegregation due to the unbalanced cooling condition and gravitational effect. In order to control the defect, a low frequency electromagnetic field has been applied in the HDC casting process and its influences on cast surface, microstructures and macrosegregation have been studied. The results show that the low frequency electromagnetic field can effectively improve surface quality, reduce inhomogeneous microstructures and macrosegregation in HDC product; and two main parameters of the electromagnetic field—density and frequency, significantly influence the microstructures and solution distribution along the diameter of the ingot. In the range of ampere-turns and frequency employed in the experiments, the optimum ampere-turns and frequency are found to be 10,000At, 30Hz.
Effects of Low-Frequency Electromagnetic Field on Microstructure and Macrosegregation of HDC Casting 2024 Aluminum Alloy

ZHU Qing-feng,ZHAO Zhi-hao,CUI Jian-zhong,WANG Jing

DOI: https://doi.org/10.3321/j.issn:1005-3026.2007.07.022

2007-01-01

Abstract:Investigates experimentally and comparatively the as-cast microstructure and Cu macrosegregation of 2024 Al alloy ingots by HDC(horizontal direct chill) continuous casting process in low-frequency electromagnetic field and those by conventional horizontal continuous casting process,where the cross-sectional area of specimens is 40 mm×200 mm.The two different specimens were both inspected by optical microscopy and chemically analyzed sampling from their cross-sectional areas.The result showed that the low-frequency electromagnetic field can greatly improve the microstructure with grain refining,and reduce the Cu macrosegregation on cross-sectional area for uniform distribution.
Investigation on microsegregation of Al-4.5%Cu alloy produced by low frequency electromagnetic casting

Dandan Chen,zhang haishou,Xiangjie Wang,Jianzhong Cui

DOI: https://doi.org/10.3724/SP.J.1037.2010.00427

2011-01-01

Abstract:Microsegregation caused by the redistribution of alloying elements means the inhomogeneity of the chemical composition on the scale of a single grain. To decrease the degree of microsegregation is beneficial to avoiding ingots hot crack and shortening the homogenizing treatment time. In this study, the microsegregation of Cu element in the Al-4.5%Cu (mass fraction) alloy was investigated. Al-4.5%Cu ingots with diameter of 200 mm were prepared by the processes of conventional direct chill (DC) casting and low frequency electromagnetic casting (LFEC), respectively. The temperatures were measured during solidification processes. The effects of low frequency electromagnetic field on the microstructures and microsegregation of Cu element were investigated from eutectic analysis and electro probe microanalysis (EPMA). By the OM observations, it was found that the area fraction and dimensions of eutectic decreased markedly. The concentration profiles of Cu element were obtained with EPMA results, which showed that the profiles increased (i.e. the content of Cu element in α-Al phase increased) in the initial transit region due to the effect of low frequency electromagnetic field. The effective distribution coefficient ke of Cu element was calculated. In the initial transit region, ke increased to unit linearly. At the same time, the low frequency electromagnetic field made ke a bigger value, and the value increased with the increasing of the current intensity. Because the cooling rate at the solidification front was promoted by the low frequency electromagnetic field, and there was more Cu element in α-Al, the microsegregation of Cu element in the ingot was alleviated by the LFEC process. © Copyright.
Effects of the Low Frequency Electromagnetic Field on the Centerline Macrosegregation of 7075 Aluminum Ingots

Dandan Chen,Haitao Zhang,Xiangjie Wang,Jianzhong Cui

DOI: https://doi.org/10.4028/www.scientific.net/amr.295-297.1705

2011-01-01

Advanced Materials Research

Abstract:The effects of the low frequency electromagnetic field on the macrosegregation of the 7075 aluminum ingots were investigated. The 7075 aluminum ingots with the diameter of 200 mm were prepared by the conventional direct chill casting and the low frequency electromagnetic field casting (LFEC) processes, respectively. The temperature during casting at steady state was measured, and the mushy region was observed from the temperature contour. The concentrations of the alloying elements were measured by the spectrograph. It was found that the transition region was broadened, but the mushy zone became narrower with presence of the low frequency electromagnetic field. The centerline macrosegregation of the ingots was alleviated by the low frequency electromagnetic casting process.
Effects of Low Frequency Electromagnetic Field on Segregation Layer During Hot-Top Casting of Aluminium Alloy

Xiangjie Wang,Jianzhong Cui,Haitao Zhang,Huixue Jiang,Gaosong Wang

DOI: https://doi.org/10.4028/www.scientific.net/amr.189-193.3795

2011-01-01

Advanced Materials Research

Abstract:Surface segregation layer are frequently encountered during aluminium alloy direct chill casting process, and the removal of the surface segregation layer before further processing of the ingot decreases the ingot yield. In this work, the low frequency electromagnetic field was applied to study the effects of low frequency electromagnetic field on segregation layer during the direct chill casting process. The results show that under the effect of the low frequency electromagnetic field, the surface quality of ingot is improved, the structure of the ingot is refined, and the thickness of segregation layer is decreased.
Effect of Low-Frequency Electromagnetic Field on Microstructure of Hypereutectic Al-Si Alloys

QIN Ke,CUI Jian-zhong,HIROMI Nagaumi,ZHANG Hai-tao

DOI: https://doi.org/10.3321/j.issn:1005-3026.2007.10.010

2007-01-01

Abstract:The influence of low-frequency electromagnetic field on microstructure and morphology of primary Si particles of Al-19.2%Si alloy ingot specimens prepared by semicontinuous casting process was investigated with electronic optical microscopy,where the specimens were taken from different parts of the cast to which different electromagnetic fields are applied.The results showed that when applying the low-frequency electromagnetic field to the casting process the microstructure can be improved obviously with the sump in melt decreased due to more uniform temperature distribution in comparison with DC casting,especially efficient refinement of primary Si particles along with the increasing magnetic field intensity is shown.However,the increasing frequency of electromagnetic field will result in bigger primary Si particle size.In this experiment,the finest size of primary Si particles is found at 15 Hz under 12 000 At.
Experimental and Numerical Study of the Influence of A Low-Frequency Electromagnetic Field on the As-Cast Structure of Horizontal Direct Chill Casting Aluminum Alloy Slab

Zhihao Zhao,Jianzhong Cui,Qingfeng Zhu,Gaosong Wang

DOI: https://doi.org/10.4028/www.scientific.net/amr.79-82.1265

2009-01-01

Advanced Materials Research

Abstract:The influences of low frequency electromagnetic field on the as-cast structure of horizontal direct chill casting aluminum alloy slab were experimental and numerical studied. The results of numerical analysis show that the interaction of the low-frequency electromagnetic field and the melt can generate an electromagnetically induced forced flow in the melt, which, in turn, changes flow pattern and temperature field in the mold. the as-cast structure of slab can be greatly improved by the changes of flow pattern and temperature field. The results of experimental analysis show that the grains of low frequency electromagnetic casting (LFEC) are fine, uniform, equiaxed, rosette-shaped; the surface of the slab of LFEC has no cold shut and less exudations. Moreover, the low-frequency electromagnetic field can improve the distribution of solute elements in the slab. The macrosegregation such as negative segregation and gravity segregation were reduced, which results in the homogenous distributions of the solute elements over the cross-section of the slab.
Improved Microstructural and Mechanical Properties Inhomogeneity of a Large-Scale AZ91D Magnesium Alloy Billet by Low-Frequency Electromagnetic Casting

Biaobiao Liu,Lei Song,Hongxia Wang,Jian Wang,Quanfu Zhang,Naidong Ren,Lifei Wang,Weili Cheng,Hua Hou,Kwang Seon Shin

DOI: https://doi.org/10.1007/s12540-024-01823-5

IF: 3.451

2024-01-01

Metals and Materials International

Abstract:The effects of low-frequency electromagnetic field on the homogeneity of microstructure and mechanical properties of Φ530 mm AZ91D magnesium alloy were investigated. Given the Lorentz force, velocity variations and temperature distribution under different electromagnetic conditions, the grain refinement mechanism and improving microstructure uniformity by low-frequency electromagnetic field were discussed in detail. Results show that the grain sizes decreased from 224.91–355.29 μm (direct-chill (DC) casting) to 203.91–235.56 μm at the frequency of 17 Hz, and the thick dendrites disappeared. The low-frequency electromagnetic field can increase the nucleation driving force of α-Mg and reduce the critical nucleus radius, thereby enhancing the nucleation rate. Additionally, forced convection could reintroduce fractured dendrites into the melt, thereby promoting heterogeneous nucleation. The precipitation of the β-Mg17Al12 was promoted as a result of the low-frequency electromagnetic field accelerating the cooling rate of the melt. Al3+ moved in a helical trajectory towards the edge of the ingot under the influence of the magnetic field, resulting in a significantly higher content of the β-Mg17Al12 at R/2 and the edge of the ingot. In addition, the application of a low-frequency electromagnetic field enhanced the mechanical properties of the alloy while diminishing the performance disparity between different regions of the casting.
Experimental Investigation of Microsegregation in Low Frequency Electromagnetic Casting 7075 Aluminum Alloy

D. Chen,H. Zhang,H. Jiang,J. Cui

DOI: https://doi.org/10.1002/mawe.201100772

2011-01-01

Materialwissenschaft und Werkstofftechnik

Abstract:7075 aluminum alloy ingots were prepared by the process of low frequency electromagnetic casting (low frequency electromagnetic casting = LFEC) and conventional direct chill (direct chill = DC) casting, respectively. The effects of low frequency electromagnetic field on microsegregation were investigated from eutectic analysis and electro probe microanalysis (EPMA). It was found that the amount of the eutectic, which was composed of alpha-Al (aluminum phase), T phase and MgZn(2) was decreased markedly. In contrast, the solute concentration profiles which depend on solid fraction were increased to a certain extent with the presence of low frequency electromagnetic field. The effective distribution coefficient k(e) was calculated, and the values of k(e) for solutes in the LFEC sample were bigger than those in the DC sample. The LFEC process alleviated the microsegregation in 7075 aluminum alloy.

Correction: Wang, F., et al. Effect of Low-Frequency Electromagnetic Casting on Micro-Structure and Macro-Segregation of 5A90 Alloy Ingots. Materials 2020, 13, 2720

Effect of Low-Frequency Electromagnetic Casting on Micro-Structure and Macro-Segregation of 5A90 Alloy Ingots

Microstructure and Tensile Properties of 5A90 Al–Mg–Li Alloy Containing Minor Sc Cast by Low-Frequency Electromagnetic Casting

Study on Micro-Structure, Solid Solubility and Tensile Properties of 5A90 Al–Li Alloy Cast by Low-Frequency Electromagnetic Casting Processing

Experimental Investigation of Microsegregation in Low Frequency Electromagnetic Casting of Al-4.5%Cu Binary Alloy

Effect of Electromagnetic Field on Microstructure and Macrosegregation of Flat Ingot of 2524 Aluminium Alloy

Effect of low-frequency electromagnetic field on microstructures and macrosegregation of ?270 mm DC ingots of an Al?Zn?Mg?Cu?Zr alloy

Effects of Low Frequency Electromagnetic Field on the Solidification Structure of Al-4.5%Cu Alloy During Level Casting Process

Effects of low-frequency electromagnetic field on microstructures and macrosegregation of continuous casting 7075 aluminum alloy

Effect of Low Frequency Electromagnetic Field on Microstructures and Macro-Segregation of Direct Chill Casting Al-19.2%Si Alloys

Effect of Low Frequency Electromagnetic Casting on Microstructure and Properties of 4045 Alloy

Correction: Chen et al. Evolution of Microstructure in Welding Heat-Affected Zone of G115 Steel with the Different Content of Boron. Materials 2022, 15, 2053.

Effect of Low-Frequency Magnetic Field on Microstructures and Macro Segregation of Horizontal Direct Chill Casting 7075 Aluminum Alloy

Effects of Low-Frequency Electromagnetic Field on Microstructure and Macrosegregation of HDC Casting 2024 Aluminum Alloy

Investigation on microsegregation of Al-4.5%Cu alloy produced by low frequency electromagnetic casting

Effects of the Low Frequency Electromagnetic Field on the Centerline Macrosegregation of 7075 Aluminum Ingots

Effects of Low Frequency Electromagnetic Field on Segregation Layer During Hot-Top Casting of Aluminium Alloy

Effect of Low-Frequency Electromagnetic Field on Microstructure of Hypereutectic Al-Si Alloys

Experimental and Numerical Study of the Influence of A Low-Frequency Electromagnetic Field on the As-Cast Structure of Horizontal Direct Chill Casting Aluminum Alloy Slab

Improved Microstructural and Mechanical Properties Inhomogeneity of a Large-Scale AZ91D Magnesium Alloy Billet by Low-Frequency Electromagnetic Casting

Experimental Investigation of Microsegregation in Low Frequency Electromagnetic Casting 7075 Aluminum Alloy