Abstract:A two-dimensional model for the simulation of solidification microstructure in multi-component alloy systems has been developed. The model is based on a cellular automaton (CA) technique for the calculation of the evolution of solid/liquid (S/L) interface. The dynamics of the interface is controlled by temperature, solute diffusion and Gibbs-Thomson effects. The diffusion equation for the temperature with release of latent heat on the S/L interface is valid in the entire domain, and the solute diffusion equation is also used in the entire domain through potential functions. Two methods are proposed to calculate the increment of the solid fraction. The first method is based on the level rule method similar to the one proposed by Jacot et al., but without the assumption of uniform temperature on the scale of the calculation domain. The second one is based on the calculation of the S/L interface velocity, which generalizes the results of Nastac and Beltran-Sanchez et al. for two-component alloy systems. If the concentration of one of the solutes tends to zero, both proposed methods reduce to the methods in Jacot et al. and Beltran-Sanchez et al. for two component alloy systems. Mesh independency is achieved by both methods and the dendritic morphologies obtained are the same if the mesh is fine enough. However, the morphologies of equiaxed dendrites calculated by using the interface velocity tends to the stable form more easily than those calculated using the level rule method as the mesh size is refined. For two-component alloy systems, the predictions of LGK theory for the steady-state tip velocity are compared with simulated values as a function of melt undercooling, which shows good agreement at very large range of undercooling. The simulated primary arm spacing in directional solidification is compared with experimental results for Fe-Si-Mg alloys and good agreement is also observed. It is noted that both methods for computing the solid fraction can be used for any multi-component alloy systems provided that the thermodynamic data are given

A simple criterion for the selection of interfacial active element to control liquid-liquid decomposition of immiscible alloys

Effects of Element Addition on Liquid Phase Separation of Bi-Ga Immiscible Alloy: Characterization by Electrical Resistivity and Coordination Tendency

Liquid Phase Separating Mechanism and Preparation Techniques of Immiscible Alloys

Depressing Liquid Phase Separation and Macrosegeregation of Fe–Sn Immiscible Alloys by Cu Alloying

First-Principles Investigation of the Interfacial Stability, Precipitate Formation, and Mechanical Behavior of Al3Li/Al3Zr/Al Interfaces

First-principles study of effects of alloying elements on Cu/γ-Fe interfacial properties

Research on the Solid-Liquid Interface Stability of Multicomponent Alloys with CALPHAD Method

Theoretical design and distribution control of precipitates and solute elements in Al−Zn−Mg−Cu alloys with heterostructure

Interaction between L2 droplets and L1/L interface in solidifying Al–Bi immiscible alloy

Engineering liquid-liquid interfaces for high-entropy alloy synthesis

A Cellular Automaton Technique for the Modeling of Solidification Microstructure in Multi-Component Alloys

Interface-Driven Solid-State Alloying in an Immiscible Cu-W System

Coexistence of multiple interfacial states at heterogeneous solid/liquid interface

The first-principles study of interfacial bonding strength and segregation behavior of alloyed elements at the η(MgZn 2 )/Al interface

First-principle investigation on the interfacial structure evolution of the δ'/θ'/δ' composite precipitates in Al-Cu-Li alloys

The Correlation Between Chemical Effect and Segregation Behavior in Metallic Al Liquid

Investigating interfacial segregation of Ω /Al in Al-Cu alloys: A comprehensive study using density functional theory and machine learning

Ab initio molecular dynamics study on the local structures and solid/liquid interface in liquid Al-Ti and Al-B-Ti alloys

Proposed Definition of Microchemical Inhomogeneity and Application To Characterize Some Selected Miscible/Immiscible Binary Metal Systems

Interface Alloying Design to Improve the Dispersion of TiB<sub>2</sub> Nanoparticles in Al Composites: A First-Principles Study

Design Method of Immiscible Dissimilar Welding (mg/fe) Based on CALPHAD and Thermodynamic Modelling