Abstract:The bottleneck problems of SiC particles reinforced AlSi10Mg composites (SiC/AlSi10Mg) prepared by traditional casting method, such as composition segregation, interface reaction and coarse microstructure, can be effectively improved by powder metallurgy with lower processing temperature. In this study, the influence of SiC particle size and content on the properties of SiC/AlSi10Mg was systematically analyzed. SiC/AlSi10Mg composites were prepared by planetary ball milling, spark plasma sintering (SPS) and hot extrusion composite preparation process. The obtained composites presents dense microstructure without the formation of interfacial reaction phase. The distribution of micron SiC particles (μm-SiC) in the matrix is relatively uniform, and nano SiC particles (nm-SiC) slightly agglomerates with the increase of the content. The strength of SiC/AlSi10Mg increases with the increase of nm-SiC content, which is mainly attributed to dispersion strengthening, dislocation strengthening and grain refinement strengthening. The strength of SiC/AlSi10Mg hardly changes with the increase of μm-SiC content, but the elongation decreases gradually. The deformation between μm-SiC and AlSi10Mg matrix is not coordinated and μm-SiC cleave the AlSi10Mg matrix. The irregular boundaries of μm-SiC are easy to produce stress concentration during loading, leading to interface cracking or μm-SiC fracture. Therefore, μm-SiC are difficult to play a significant strengthening effect to composites. With the increase of SiC content, the fracture mechanism of composites gradually changes from ductile fracture to brittle fracture in SiC agglomeration region. This study lays a theoretical and experimental foundation for the controllable preparation and performance optimization of high strength and toughness AMCs reinforced by SiC particles.

Application of Stirring Casting Method on Preparation of SiC_p/Al Composite Material

Stir casting process for manufacture of Al–SiC composites

Effects of SiC Particle Pretreatment and Stirring Parameters on the Microstructure and Mechanical Properties of SiCp/Al–6.8Mg Composites Fabricated by Semi-Solid Stirring Technique

3D microstructure simulation of stir casting SiCp/Al-7.0%Si composites

Effect of the Stirring Velocity and the SiO 2 Precursor Particles Feeding Rate on the Microstructure of the Al 2 O 3 /SiO 2 /Al Composites Prepared via Stir Casting Process

Advance in Research on the Fabrication of SiCp/Al Composites by Stir-casting Process

Air-isolated stir casting of homogeneous Al-SiC composite with no air entrapment and Al4C3

Effects of Stirring Time and Extrusion on Microstructures and Mechanical Properties of SiC Reinforced Pure Al Matrix Composites

Numerical simulation of microstructure for stir casting of Al-Si/SiC p composites with particle pushing model

Numerical Simulation of Microstructure of Al-Si/Sicp Composites During Stir Casting Process with Particle Pushing Model

Influence of characteristic parameters of SiC reinforcements on mechanical properties of AlSi10Mg matrix composites by powder metallurgy

Processing and Mechanical Properties of Sic Particulate Reinforced Az91 Composites Fabricated by Stir Casting

Fabrication Process of SiCp/7085 Composite and Experiment Research

Particle agglomeration and mechanical properties of SiCp/Al-Si composites

Damping and mechanical properties of SiC particles reinforced aluminium matrix composites prepared by colloidal dispersion and suction filtration method

Pretreatment Process of SiC Particles and Fabrication Technology of SiC Particulate Reinforced Zn–Al Alloy Matrix Composite

Study of Sicp/Az61 Composites

Squeeze casting technique for fabricating SiCp/Al composites with lower volume fractions of SiC particles

Preparation and Characterization of SiC/Al2O3 Composites

Microstructural analysis of SiCp/Al composites

Aluminum Silicon Carbide Particulate Metal Matrix Composite Development Via Stir Casting Processing