Abstract:In a comprehensive study, effects of casting methods such as gravity sand casting, squeeze casting and composite casting in semi-solid state and casting variables (i.e., cooling rate, stirring speed and shear forces) on the microstructure, porosity formation and mechanical properties of A356–SiC nanocomposites were investigated thoroughly. First, a step-like sample was used to make the sand casting samples to study the effects of different cooling rates that each step experienced on the properties of nanocomposite, where squeeze casting and composite casting samples were produced in a metallic mold. Once the samples were produced and prepared for the studies, grain size, shape factor, dendritic and globular microstructure, amount of eutectic phase and mechanism of porosity formation, mechanical properties and fracture surface of the samples were analyzed precisely and discussed. In addition, the effects of stirring forces, time and temperature, used in the squeeze casting and the compo-casting methods, on the morphology of the dendritic arms of aluminum matrix composites were investigated and compared with the microstructure of castings produced by conventional gravity casting. It was discovered that switching from the gravity sand casting process to the squeeze casting process delivers a less dendritic and more refined microstructure in the nanocomposite. However, composite castings produced in the semi-solid state by applying high stirring shear forces for 80 s produce the finest and the most globular and spherical microstructure. This optimized globularization condition provides desired microstructure and mechanical properties for this type of nanocomposite. The dominant failure mechanism in the composite casting samples produced in semi-solid state was ductile, where it was a mix of ductile/brittle for the squeeze casting and brittle for the sand casting samples. Finally, the effects of globularization temperature on the nucleation and growth of primary α grains were studied.

Stir casting process for manufacture of Al–SiC composites

Application of Stirring Casting Method on Preparation of SiC_p/Al Composite Material

Effect of the Stirring Velocity and the SiO 2 Precursor Particles Feeding Rate on the Microstructure of the Al 2 O 3 /SiO 2 /Al Composites Prepared via Stir Casting Process

Effects of SiC Particle Pretreatment and Stirring Parameters on the Microstructure and Mechanical Properties of SiCp/Al–6.8Mg Composites Fabricated by Semi-Solid Stirring Technique

Processing and Mechanical Properties of Sic Particulate Reinforced Az91 Composites Fabricated by Stir Casting

Exploring tribological properties in the design and manufacturing of metal matrix composites: an investigation into the AL6061-SiC-fly ASH alloy fabricated via stir casting process

Air-isolated stir casting of homogeneous Al-SiC composite with no air entrapment and Al4C3

Microstructure, phase compositions and mechanical properties of slip cast sintered SiC/Si3N4 composites

Aluminum Silicon Carbide Particulate Metal Matrix Composite Development Via Stir Casting Processing

Optimization of process variables and characterization of mechanically agitated ceramic‐microsphere reinforced aluminium composite

Effects of Stirring Time and Extrusion on Microstructures and Mechanical Properties of SiC Reinforced Pure Al Matrix Composites

Numerical Simulation of Microstructure of Al-Si/Sicp Composites During Stir Casting Process with Particle Pushing Model

Influence of the Grit size of Silicon Carbide Particles on the Mechanical and Electrical Properties of Stir Casting Aluminum Matrix Composite Material

3D microstructure simulation of stir casting SiCp/Al-7.0%Si composites

Enhancing Aluminum-Based Composite Manufacturing: Harnessing Si3N4 Reinforcement via Stir Casting Technique

Pretreatment Process of SiC Particles and Fabrication Technology of SiC Particulate Reinforced Zn–Al Alloy Matrix Composite

Influence of characteristic parameters of SiC reinforcements on mechanical properties of AlSi10Mg matrix composites by powder metallurgy

The Influence of the Casting Methods and Variables on the Microstructural Properties of A356–SiC Nanocomposite

In Situ Al Based Composites Fabricated in Al-SiO2-C System by Reaction Sintering

Processing, Microstructure and Mechanical Properties of Micro-Sic Particles Reinforced Magnesium Matrix Composites Fabricated by Stir Casting Assisted by Ultrasonic Treatment Processing

Microstructure Evolution and Mechanical Behaviors of SiCp/CNTs Hybrid Reinforced Al-Si-Cu-Mg Composite by Semi-solid Stir Casting