Abstract:The heat transfer model for steel solidification in Al 2 O 3 crucial and permanent mold by finite element method was developed and validated by temperature measurement. The multi-gradient operation was novelly designed, and the tailored cooling rate in range of 0.1–10 °C/s was obtained at the target location. The simulation aided experiment with the large-sized samples was carried out, and the local cooling rate was verified by secondary dendrite arm spacing. The size of austenite grain decreases slightly as cooling rate increases from 0.15 °C/s to 0.31 °C/s, and then increases dramatically in the range of 0.31–0.48 °C/s, finally decreases with cooling rate increasing further to 9.76 °C/s. The relationship between austenite grain size and cooling rate was logarithmically regressed in the range of 0.48–9.76 °C/s, in which the kinetic equations on basis of cooling experiment and continuously cast slab can also work. However, the grain size decrease in 0.15–0.31 °C/s and then increase in 0.31–0.48 °C/s cannot be described. Based on the mechanism of peritectic solidification, the austenite grain growth is mainly controlled by diffusion at a low cooling rate smaller than 0.31 °C/s, and the final grain size is less than 1.0 mm. At a medium cooling rate between 0.48 and 3.60 °C/s, austenite grain growth is accelerated by the energy stored during massive type peritectic transformation previously, and the grain size is between 1.7 and 2.9 mm. At high cooling rate larger than 9.76 °C/s, austenite grains grow to about 0.9 mm in columnar shape. The time for grain growth is not adequate, although addition energy storage by massive transformation can also occur. The critical cooling rate for the onset of massive type peritectic transformation in the large-sized sample is between 0.31 and 0.48 °C/s. The growth velocity in the isothermal experiment is much smaller than that in continuous cooling process, confirming that the austenite grain evolution is significantly affected by previous peritectic solidification.

Influences of cooling rates on delta ferrite of nuclear power 316H austenitic stainless steel

Effect of Cooling Rate on Solidification Microstructures in AISI 304 Stainless Steel

Microstructural evolution in 316LN austenitic stainless steel during solidification process under different cooling rates

Influences of Cooling Rates on Solidification and Segregation Characteristics of Fe-Cr-Ni-Mo-N Super Austenitic Stainless Steel

Formation Mechanism and Structure Evolution of Austenitic Stainless Steel 304 during Solidification with Near-Rapid Rates

Effect of Cooling Rate on Crystallization Behavior during Solidification of Hyper Duplex Stainless Steel S33207: An In Situ Confocal Microscopy Study

Effect of Cooling Rate on Microstructure and Mechanical Properties of a Microlaminated Low-Density Steel

Effect of Cooling Rate on the Grain Morphology and Element Segregation Behavior of Fe-Mn-Al-C Low-Density Steel During Solidification

Austenite grain growth in tailored cooling rate experiment designed by numerical simulation for peritectic steel

Effects of Cooling Rate and Vanadium on δ→γ Phase Transformation in Low Carbon Steel

Effect Mechanism of α-Ferrite Sustained Precipitation on High-Temperature Properties in Continuous Casting for Peritectic Steel

Effects of Cooling Rate on Microstructure, Mechanical Properties, and Residual Stress of Fe-2.1B (wt%) Alloy

In situ observation of the austenite to ferrite transformation in low-carbon steels from different initial phases at defined cooling rates

Effects of cooling manner on Laves phase precipitation and mechanical properties of Al modified super ferritic stainless steels

Effect of Si on δ‐ferrite/γ‐austenite transformation and M23C6 precipitation during solidification of X10CrAlSi18 ferritic heat‐resistant stainless steel

Influence of Cooling Rate on Microstructure Evolution and Pitting Corrosion Resistance in the Simulated Heat-Affected Zone of 2304 Duplex Stainless Steels

Secondary Phase Precipitation in Fe-22Mn-9Al-0.6C Low-Density Steel during Continuous Cooling Process

Influence of Cooling Rate on Precipitated Phase of Super Duplex Stainless Steel

Influence of High-Temperature Deformation on the Dissolution of δ-Ferrite in Stainless Steels

Modelling of Delta Ferrite to Austenite Phase Transformation Kinetics in Martensitic Steels: Application to Rapid Cooling in Additive Manufacturing

Effect of austenitizing temperature and cooling rate on Ms temperature of Fe–Ni–Cr cast iron