Abstract:The heat transfer model for steel solidification in Al 2 O 3 crucial and permanent mold by finite element method was developed and validated by temperature measurement. The multi-gradient operation was novelly designed, and the tailored cooling rate in range of 0.1–10 °C/s was obtained at the target location. The simulation aided experiment with the large-sized samples was carried out, and the local cooling rate was verified by secondary dendrite arm spacing. The size of austenite grain decreases slightly as cooling rate increases from 0.15 °C/s to 0.31 °C/s, and then increases dramatically in the range of 0.31–0.48 °C/s, finally decreases with cooling rate increasing further to 9.76 °C/s. The relationship between austenite grain size and cooling rate was logarithmically regressed in the range of 0.48–9.76 °C/s, in which the kinetic equations on basis of cooling experiment and continuously cast slab can also work. However, the grain size decrease in 0.15–0.31 °C/s and then increase in 0.31–0.48 °C/s cannot be described. Based on the mechanism of peritectic solidification, the austenite grain growth is mainly controlled by diffusion at a low cooling rate smaller than 0.31 °C/s, and the final grain size is less than 1.0 mm. At a medium cooling rate between 0.48 and 3.60 °C/s, austenite grain growth is accelerated by the energy stored during massive type peritectic transformation previously, and the grain size is between 1.7 and 2.9 mm. At high cooling rate larger than 9.76 °C/s, austenite grains grow to about 0.9 mm in columnar shape. The time for grain growth is not adequate, although addition energy storage by massive transformation can also occur. The critical cooling rate for the onset of massive type peritectic transformation in the large-sized sample is between 0.31 and 0.48 °C/s. The growth velocity in the isothermal experiment is much smaller than that in continuous cooling process, confirming that the austenite grain evolution is significantly affected by previous peritectic solidification.

Formation Mechanism and Structure Evolution of Austenitic Stainless Steel 304 during Solidification with Near-Rapid Rates

Microstructure evolution in AISI 304 stainless steel during near rapid directional solidification

Microstructural evolution in 316LN austenitic stainless steel during solidification process under different cooling rates

Influences of Cooling Rates on Solidification and Segregation Characteristics of Fe-Cr-Ni-Mo-N Super Austenitic Stainless Steel

Evolution of primary carbides during accelerated solidification process of high-carbon martensitic stainless steels

Effect of Cooling Rates on the Local—Overall Morphology Characteristics of Solidification Structure at Different Stages for High Carbon Steel

Solidification Structures of Fe–Cr–Ni–Mo–N Super-austenitic Stainless Steel Processed by Twin-roll Strip Casting and Ingot Casting and Their Segregation Evolution Behaviors

Effect of Cooling Rate on Crystallization Behavior during Solidification of Hyper Duplex Stainless Steel S33207: An In Situ Confocal Microscopy Study

Austenite grain growth in tailored cooling rate experiment designed by numerical simulation for peritectic steel

Influences of cooling rates on delta ferrite of nuclear power 316H austenitic stainless steel

In situ observation of the austenite to ferrite transformation in low-carbon steels from different initial phases at defined cooling rates

Structure and Martensitic Transformation in Rapidly Solidified CoNiAlFe Alloy

Effect of Cooling Rate on Microstructure and Mechanical Properties of a Microlaminated Low-Density Steel

Kinetic Transitions and Mn Partitioning During Austenite Growth from a Mixture of Partitioned Cementite and Ferrite: Role of Heating Rate

Experimental simulation on the continuous casting solidified structure of S32205 duplex stainless steel

Effect of cooling rate on microstructure and mechanical properties of a low-carbon low-alloy steel

Unlocking the Mechanisms behind Austenite Formation of Cold‐Rolled Ferrite–Martensite Dual‐Phase Steels: The Role of Ferrite Recrystallization

On Microstructure Characterization of Fe–Cr–Ni–Mo–N Super-Austenitic Stainless Steel During Hot Deformation

Solidification of Tungsten Inert Gas–Welded Austenitic Stainless Steel with 0.17 wt% N

Austenite Growth Behavior of Fe-13 Cr-5 Ni Martensitic Stainless Steel under Continuous Heating

Study of High-Strength Austenitic Nitrogen-Containing Steel Ingot Phase Formation and Structure