Abstract:In this paper, the effect of Si content on the microstructure and mechanical properties of the Al–1.2Mg– x Si–1.2Cu–0.6Mn cast alloy was investigated. The study aimed to explore the optimal addition of Si element to improve the comprehensive properties of alloys. The microstructure, phase composition and fracture morphology of the alloy were determined through OM, SEM, EBSD and XRD analysis. The Si content in the alloy ranged from 0.48 to 2.4 wt.%. With the increase of Si content, the number of strengthening phases increases, which improves the comprehensive properties of the alloy. When the Si content is 0.8 wt.%, the eutectic Mg 2 Si transforms from rod-shaped to larger block shaped, and the formation of coarse Mg 2 Si phase limits the elongation of the alloy. When the Si content is 2.4 wt.%, fine Al 2 Cu phases are present in this alloy and coexist with Al(Fe,Mn)Si phases, while an increase in the Si content appears as partially accompanied by an incipient crystalline Si phase around the Al(Fe,Mn)Si phase. The alloy exhibits a maximum tensile strength, yield strength and elongation of 198.2 MPa, 101.2 MPa and 4.96%, respectively, with a hardness of 80.94 Hv. It consists of five alloy phases, mainly α-Al, Mg 2 Si, Al(Fe, Mn)Si eutectic phase, Q-AlCuMgSi eutectic phase and the beginning crystalline silicon phase formed due to the increased Si content. The Si content can improve alloy strength, but there is some damage to the toughness of the alloy. Higher silicon alloy content results in the formation of fine Al 2 Cu eutectic. This result makes it possible to achieve a higher level of strength with a reduced loss of ductility in the alloy.

Effect of Ag Content on the Microstructures and Mechanical Properties of Mo-12Si-8.5B Alloy

The Effect of A Small Amount of Tungsten on the Microstructure of Mechanically Alloyed Ag37cu63

EFFECTS OF Ag CONTENT ON MICROSTRUCTURE AND PROPERTIES OF THE FILAMENT STRENGTHENED Cu-Ag ALLOYS

Effects of Lanthanum Oxide Content on Mechanical Properties of Mechanical Alloying Mo–12Si–8.5B (at.%) Alloys

Microstructure, Mechanical Properties, and Corrosion Behavior of Al-4.0Cu-1.1Li-0.5Mg-xAg Alloys

The Effect of Solution Treatment on the Si Particles’ Morphology Evolution and the Thermal Conductivity and Tensile Properties of Sb-Modified Al-8Si-0.6Mg Alloys

Influence of Ag Contents on Structure and Tribological Properties of TiSiN-Ag Nanocomposite Coatings on Ti–6Al–4V

Influences of the Ag Content on Microstructures and Properties of Zn–3Mg–xAg Alloy by Spark Plasma Sintering

Microstructure and Mechanical Properties of Lanthanum Oxide-Doped Mo–12Si–8.5B(at%) Alloys

Effects of micro-alloying Ag on microstructure, mechanical properties and corrosion behavior of extruded Mg-2Zn-0.2Ca-xAg alloys

Effect of Cu Content on Microstructure and Mechanical Properties of Al-Cn-0.4Mg-0.6Ag Alloy

Effects of Ag Micro-Addition on Structure and Mechanical Properties of Sn-11Sb-6Cu Babbitt

Effects of Sb on Microstructure and Mechanical Properties of Mg-5.5al-1.2y Alloy

Effect of Mo Addition on Microstructures and Mechanical Properties of Ti2AlNb Alloy

The effect of Ag on the tensile strength and fracture toughness of novel Al-Mg-Zn alloys

Effect of Mn/Ag Ratio on Microstructure and Mechanical Properties of Heat-Resistant Al-Cu Alloys

Effects of Al Concentration on Microstructure and Mechanical Properties of Mg-xAl-1Zn-1Si Alloy

The Effect of Si Content on the Microstructure and Mechanical Properties of Al–1.2Mg–xSi–1.2Cu–0.6Mn Cast Alloy

The Multi-Scale Microstructure and Strengthening Mechanisms of Mo-12Si-8.5BxZr (at.%) Alloys

Influence of the Mg Content on the Microstructure and Mechanical Properties of Al-xMg-2.0Si-0.6Mn Alloy

Effects of Sb Content on Microstructure and Mechanical Properties of Mg-6Zn-Y-Zr-xSb Alloy