Abstract:The electrolysis of CO2 into value-added products holds great potential for closing the carbon cycle. A membrane electrode assembly (MEA) that uses solid polymer electrolytes is a critical technology for enhancing the energy efficiency for the CO2 reduction reaction (CO2RR) because a thin electrolyte layer can effectively reduce the ohmic resistance. The stable operation of the CO2RR in MEA-based cells with an anion-exchange membrane (AEM), however, is hindered by the accumulation of bicarbonate salts, which are derived from alkali-metal cations in anolytes, on the cathode side. Therefore, for stable operation of CO2 electrolysis using an MEA-based cell, the amount of alkali-metal cations needs to be reduced. However, the minimal amount of alkali-metal cations required to operate the reaction system has not been elucidated. Quantitative analysis of the amount of alkali-metal cations transported from the anode to the cathode is essential to obtain the insight into the necessary amount for the operation. In this study, we conducted a quantitative evaluation of the correlation between the production of high-value C2+ compounds, such as ethylene and ethanol, and the transported alkali-metal cations. As a result, although the presence of transported alkali-metal cations on the cathode surface significantly contributes to the generation of C2+ compounds, the rate of K+ ion transport did not match the selectivity of C2+. This result suggests a continuous supply of high amount of K+ to the cathode surface is not required for C2+ formation. On the basis of these findings, we achieved a faradaic efficiency (FE) and a partial current density for C2+ of 77% and 230 mA cm−2, respectively, even after switching the anode solution from 0.1 M KHCO3 to a dilute K+ solution (<7 mM) in an MEA-based cell using AEM and Cu nanoparticles as the cathode catalyst. These values of FE and partial current density were almost identical to those when 0.1 M KHCO3 was continuously supplied as the anode solution. Based on this insight, we successfully improved the durability of the system against salt precipitation. The FE for ethylene remained constant for as long as 60 h at 150 mA cm−2 when continuously flowing 0.1 M KHCO3 as anolyte. However, the FE suddenly decreased after 60 h due to the cessation of CO2 gas flow, caused by salt precipitation in the cathode flow channel. On the contrary, by intermittently supplying 0.1 M KHCO3, we confirmed that the amount of visible K+ salt in the cathode flow field remained negligible even after more than 90 hours of stable operation.

Quantitative Analysis and Manipulation of Alkali Metal Cations at the Cathode Surface in Membrane Electrode Assembly Electrolyzers for CO2 Reduction Reactions

Suppression of Salt Precipitation in Membrane Electrode Assembly Electrolyzers for CO2 reduction reactions by Intermittent Supply of Alkali Metal Cations

Anchoring Cs+ Ions on Carbon Vacancies for Selective CO2 Electroreduction to CO at High Current Densities in Membrane Electrode Assembly Electrolyzers

Alkali metal cations enhance CO2 reduction by a Co molecular complex in a bipolar membrane electrolyzer

Anolyte Enhances Catalyst Utilization and Ion Transport Inside a CO2 Electrolyzer Cathode

CO2 Loss into Solution: An Experimental Investigation of CO2 Electrolysis with a Membrane Electrode Assembly Cell

Immobilized Tetraalkylammonium Cations Enable Metal‐free CO2 Electroreduction in Acid and Pure Water

A Solid-State Electrolyte Facilitates Acidic CO2 Electrolysis without Alkali Metal Cations by Regulating Proton Transport

(Invited) Effects of the Local Chemical Environment on the Anode and Cathode Processes of CO2 Electrolyzers

Enhancing Local CO 2 Concentration via Covalent Interaction for the Conversion of Carbonate to CO

Confinement of an Alkaline Environment for Electrocatalytic CO2 Reduction in Acidic Electrolytes.

A Solid-State Electrolyte Facilitates Acidic CO 2 Electrolysis without Alkali Metal Cations by Regulating Proton Transport

Self-Cleaning CO 2 Reduction Systems: Unsteady Electrochemical Forcing Enables Stability

Unintended cation crossover influences CO2 reduction selectivity in Cu-based zero-gap electrolysers

Surface-immobilized cross-linked cationic polyelectrolyte enables CO2 reduction with metal cation-free acidic electrolyte

Improved CO Selectivity via Anion Exchange Membrane Electrode Assembly‐Type CO2 Electrolysis with an Ionomer‐Coated Zn‐Based Cathode

Towards membrane-electrode assembly systems for CO2 reduction: a modeling study

Dynamic Cation Enrichment during Pulsed CO2 Electrolysis and the Cation-Promoted Multicarbon Formation

Alkaline anion exchange membrane water electrolysis: Effects of electrolyte feed method and electrode binder content

Alkali Metal Cations Induce Structural Evolution on Au(111) During Cathodic Polarization

Direct Membrane Deposition for CO 2 Electrolysis