Abstract:Ethylene is one of the largest building blocks in the petrochemical industry, mainly produced by steam cracking of ethane derived from naphtha or shale gas at high temperatures (>800 °C). Despite its technical maturity and economic competitiveness, the thermal steam cracking of ethane is highly energy-intensive. Herein, an electrochemically engineered direct conversion process of ethane to produce hydrogen and ethylene using a planar protonic ceramic membrane reactor with a bi-functional three-dimensional catalytic electrode is reported, with a single-pass ethane conversion of 40% and ethylene yield of 26.7% at 550 °C. Compared with the industrial ethane steam cracking, this method saves process energy input by 45.1% and improves process energy efficiency by 50.6%, based on comprehensive process simulation using Aspen Plus software. Further, steam electrolysis treatment under the solid oxide electrolysis cell mode can regenerate the system's catalytic performance and significantly alleviate catalytic degradation by 74%, demonstrating high techno-economic viability.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acscatal.1c03351.Fabrication procedures of electrochemical cell with 3D anode; XRD patterns and EDS mapping of PBFM material under different atmospheres; schematic of the in-house built dual-zone reactor; detailed process flow diagram of an EEDC process for Aspen Plus simulation; selectivity of various hydrocarbon products in the EEDC process at different temperatures above 600 °C under OCV conditions; C2H6 conversion and C2H4 yield at different applied currents, operating temperatures, and C2H6 feedstock concentration; electrochemical performance under EEDC and SOEC modes; results of Faraday efficiency measurement; GC raw data showing the formation of higher (C3+) hydrocarbon products in the EEDC process; TGA results and calculated coke content under different applied currents and after regeneration; C2H4 yield during each operation cycle with intermittent regeneration; cell resistance and SEM images of the integrated anode before and after the test; STEM image of PtGa/ZSM-5 catalyst before and after EEDC process; XPS result of the PtGa/ZSM-5 catalyst before and after reaction; assumptions for the Aspen Plus simulation of the EEDC process; reactions and corresponding conversions inside the EEDC reactor at 40 mA·cm–2 assumed for Aspen Plus simulation; process result summary of ethylene production from steam-ethane cracking and EEDC at an applied current density of 40 mA cm–2; specific energy input and output for the EEDC process; surface chemical composition of the PtGa/ZSM-5 catalyst before and after reaction (PDF)This article has not yet been cited by other publications.

Electrochemically Engineered, Highly Energy-Efficient Conversion of Ethane to Ethylene and Hydrogen below 550 °C in a Protonic Ceramic Electrochemical Cell

An Efficient Tri‐Conductive Electrode for Ethane Direct Electrochemical Dehydrogenation on Proton Ceramic Electrolysis Cells

Development and Intensification of the Ethylene Process Utilizing a Catalytic Membrane Reactor

High-Rate and Efficient Ethylene Electrosynthesis Using a Catalyst/Promoter/Transport Layer

Simultaneous Generation of Electricity, Ethylene and Decomposition of Nitrous Oxide Via Protonic Ceramic Fuel Cell Membrane Reactor

Near 100% Conversion of Acetylene to High‐purity Ethylene at Ampere‐Level Current

Electrocatalytic CO2 Reduction to Ethylene: from Advanced Catalyst Design to Industrial Applications

Anionic Ionomer: Released Surface-Immobilized Cations and an Established Hydrophobic Microenvironment for Efficient and Durable CO2-to-Ethylene Electrosynthesis at High Current over One Month

One-Step Electrochemical Ethylene-to-Ethylene Glycol Conversion over a Multitasking Molecular Catalyst.

Carbon‐Efficient CO2 Electrolysis to Ethylene with Nanoporous Hydrophobic Copper

CO Electrolysis to Multicarbon Products over Grain Boundary-Rich Cu Nanoparticles in Membrane Electrode Assembly Electrolyzers

Highly efficient ethylene production via electrocatalytic hydrogenation of acetylene under mild conditions

Enhancement of the Acetylene and Ethylene Yields from Ethane by Partially Decoupling the Oxidation and Pyrolysis Reactions

High‐rate and Selective CO2 Electrolysis to Ethylene via Metal‐Organic Framework‐augmented CO2 Availability

Ethylene and power cogeneration from proton ceramic fuel cells (PCFC): A thermo-electrochemical modelling study

Novel Sr1.95Fe1.4Co0.1Mo0.5O6-δ anode heterostructure for efficient electrochemical oxidative dehydrogenation of ethane to ethylene by solid oxide electrolysis cells

Concurrent electrocatalytic hydrogen evolution and polyethylene terephthalate plastics reforming by self-supported amorphous cobalt iron phosphide electrode

Interfacial Enhancement by Γ‐al 2 O 3 of Electrochemical Oxidative Dehydrogenation of Ethane to Ethylene in Solid Oxide Electrolysis Cells

Highly Efficient and Selective Electrocatalytic Semihydrogenation of Acetylene to Ethylene via Continuous Proton Feeding and Accelerated Transfer on Cu NP/FeNC Composite

Selective Ethylene Production from CO2 and CO Reduction via Engineering Membrane Electrode Assembly with Porous Dendritic Copper Oxide

Electrocatalytic Acetylene Hydrogenation in Concentrated Seawater at Industrial Current Densities