Abstract:Ethylene is one of the largest building blocks in the petrochemical industry, mainly produced by steam cracking of ethane derived from naphtha or shale gas at high temperatures (>800 °C). Despite its technical maturity and economic competitiveness, the thermal steam cracking of ethane is highly energy-intensive. Herein, an electrochemically engineered direct conversion process of ethane to produce hydrogen and ethylene using a planar protonic ceramic membrane reactor with a bi-functional three-dimensional catalytic electrode is reported, with a single-pass ethane conversion of 40% and ethylene yield of 26.7% at 550 °C. Compared with the industrial ethane steam cracking, this method saves process energy input by 45.1% and improves process energy efficiency by 50.6%, based on comprehensive process simulation using Aspen Plus software. Further, steam electrolysis treatment under the solid oxide electrolysis cell mode can regenerate the system's catalytic performance and significantly alleviate catalytic degradation by 74%, demonstrating high techno-economic viability.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acscatal.1c03351.Fabrication procedures of electrochemical cell with 3D anode; XRD patterns and EDS mapping of PBFM material under different atmospheres; schematic of the in-house built dual-zone reactor; detailed process flow diagram of an EEDC process for Aspen Plus simulation; selectivity of various hydrocarbon products in the EEDC process at different temperatures above 600 °C under OCV conditions; C2H6 conversion and C2H4 yield at different applied currents, operating temperatures, and C2H6 feedstock concentration; electrochemical performance under EEDC and SOEC modes; results of Faraday efficiency measurement; GC raw data showing the formation of higher (C3+) hydrocarbon products in the EEDC process; TGA results and calculated coke content under different applied currents and after regeneration; C2H4 yield during each operation cycle with intermittent regeneration; cell resistance and SEM images of the integrated anode before and after the test; STEM image of PtGa/ZSM-5 catalyst before and after EEDC process; XPS result of the PtGa/ZSM-5 catalyst before and after reaction; assumptions for the Aspen Plus simulation of the EEDC process; reactions and corresponding conversions inside the EEDC reactor at 40 mA·cm–2 assumed for Aspen Plus simulation; process result summary of ethylene production from steam-ethane cracking and EEDC at an applied current density of 40 mA cm–2; specific energy input and output for the EEDC process; surface chemical composition of the PtGa/ZSM-5 catalyst before and after reaction (PDF)This article has not yet been cited by other publications.

Simultaneous Generation of Electricity, Ethylene and Decomposition of Nitrous Oxide Via Protonic Ceramic Fuel Cell Membrane Reactor

An efficient electrode for reversible oxygen reduction/evolution and ethylene electro-production on protonic ceramic electrochemical cells

In-situ exsolved FeNi nanoparticles on perovskite matrix anode for co-production of ethylene and power from ethane in proton conducting fuel cells

Electrochemically Engineered, Highly Energy-Efficient Conversion of Ethane to Ethylene and Hydrogen below 550 °C in a Protonic Ceramic Electrochemical Cell

Synergistic Bulk and Surface Engineering for Expeditious and Durable Reversible Protonic Ceramic Electrochemical Cells Air Electrode

Co-generation of electricity and olefin via proton conducting fuel cells using (Pr0.3Sr0.7)0.9Ni0.1Ti0.9O3 catalyst layers

Improved Water Dissociation and Nitrous Oxide Decomposition by in Situ Oxygen Removal in Perovskite Catalytic Membrane Reactor

An Efficient Trifunctional Spinel‐Based Electrode for Oxygen Reduction/Evolution Reactions and Nonoxidative Ethane Dehydrogenation on Protonic Ceramic Electrochemical Cells

Ethylene and power cogeneration from proton ceramic fuel cells (PCFC): A thermo-electrochemical modelling study

An Efficient Tri‐Conductive Electrode for Ethane Direct Electrochemical Dehydrogenation on Proton Ceramic Electrolysis Cells

High-temperature Water Oxidation Activity of a Perovskite-Based Nanocomposite Towards Application As Air Electrode in Reversible Protonic Ceramic Cells

Concurrent electrocatalytic hydrogen evolution and polyethylene terephthalate plastics reforming by self-supported amorphous cobalt iron phosphide electrode

CO Electrolysis to Multicarbon Products over Grain Boundary-Rich Cu Nanoparticles in Membrane Electrode Assembly Electrolyzers

Cathode tailoring of micro-tubular protonic ceramic electrochemical reactors for CO 2 hydrogenation

Battery-Driven N2 Electrolysis Enabled by High-Entropy Catalysts: from Theoretical Prediction to Prototype Model

Catalytic ceramic oxygen ionic conducting membrane reactors for ethylene production

Barium‐doped Sr 2 Fe 1.5 Mo 0.5 O 6‐ δ perovskite anode materials for protonic ceramic fuel cells for ethane conversion

Surface restructuring of a perovskite-type air electrode for reversible protonic ceramic electrochemical cells

Mixed Oxygen Ionic and Electronic Conducting Membrane Reactors for Pure Chemicals Production

Emerging anode materials architectured with NiCoFe ternary alloy nanoparticles for ethane-fueled protonic ceramic fuel cells

Membraneless Electrochemical Synthesis Strategy toward Nitrate-to-Ammonia Conversion