Abstract:A superior combination of yield strength (1001 MPa) and − 20 °C impact toughness (166 J) was obtained in Nb–V–Ti-microalloyed Ni–Cr–Mo–Cu steel treated by direct quenching and tempering route (DQT). The tested steels treated by DQT route and re-austenitization and tempering route (QT) were compared with each other in terms of mechanical properties and microstructures characterized by optical microscopy, transmission electron microscopy, X-ray diffraction, electron back-scattered diffraction method and so on. Strength and Vickers hardness of the tested steel treated by the above two routes vary with isothermal aging temperature (400–600 °C), shown as under-aged state, peak-aged state and over-aged state. All DQT specimens show higher strength and Vickers hardness than QT specimens with the same aging condition. Furthermore, the largest difference of yield strength between DQT and QT specimens was shown in DQT600 and QT600 specimens. DQT600 or QT600 specimens refers to direct quenched (DQ) or quenched (Q) specimens isothermally aged at 600 °C. The main disparities in quenched microstructure between DQ and Q specimens are mainly in morphology of prior austenite grains, dislocation density of martensite matrix and solution amount of Nb and Mo elements dissolving in martensite matrix, which play key roles in affecting microstructure and mechanical properties of DQT and QT specimens. Higher dislocation density of matrix and finer average diameter of both MC (M is any combination of Nb, Mo and V) and Cu-rich particles were shown in DQT600 specimens than in QT600 specimens. Strengthening from dislocations and nanosized MC and Cu-rich particles mainly leads to the largest difference of yield strength between DQT600 and QT600 specimens. In addition, strong dislocation strengthening and precipitation strengthening in DQT600 specimen also elevated its ductile-to-brittle-transition-temperature, compared with QT600 specimen.

The Microstructure, Mechanical Properties, and Precipitation Behavior of 1000 MPa Grade GEN3 Steel after Various Quenching Processes

Study on Direct Quenching and Tempering Process of 1000mpa Grade Low Alloy High Strength Steel

Study of microstructural evolution and mechanical properties of 1000 MPa low-carbon microalloyed steel prepared by multiple quenching strategies near Ms

Mechanism exploration of an ultrahigh strength steel by quenching-partitioning-tempering process

Relationship Between Microstructure and Mechanical Properties of M50 Ultra-High Strength Steel Via Quenching-Partitioning-tempering Process

Microstructure and Mechanical Properties of Ultra-high Strength Q&P Steel with 3.5% Mn

Characterization of Microstructure and Mechanical Properties of a Nb-Microalloyed Steel after Quenching-Partitioning-Tempering Process

Effects of Novel Q-P-T and Traditional Q-T Processes on the Microstructure and Mechanical Properties of Martensitic Steels with Different Carbon Content

Microstructual Evolution of a Medium Carbon Advanced High Strength Steel Heat-Treated by Quenching-Partitioning Process

Microstructure and mechanical properties of 1000 MPa grade steel plate for hydropower station in different quenching processes

Novel Ultrahigh-Strength Nanolath Martensitic Steel by Quenching–partitioning–tempering Process

Study of a Novel Ultra-High Strength Steel with Adequate Ductility and Toughness by Quenching-Partitioning-Tempering Process

Effect of Modifying Matrix Microstructures and Nanosized Precipitates on Strengthening Mechanisms and Ductile-to-brittle-transition-temperature in a 1000 MPa Ni–Cr–Mo–Cu Steel

A novel microstructural design and heat treatment technique based on gradient control of carbon partitioning between austenite and martensite for high strength steels

Ultrahigh strength-ductility steel treated by a novel quenching–partitioning–tempering process

Microstructural Evolution of Medium Carbon Steels during the Quenching and Partitioning Process

Room-Temperature Quenching and Partitioning Steel

Study on the Mechanism of Excellent Strength and Toughness Combination of a High Nitrogen Martensitic Stainless Steel Treated by Q-C-P-T Process

Enhancement of the mechanical properties of a Nb-microalloyed advanced high-strength steel treated by quenching–partitioning–tempering process

Quenching-Partitioning-Tempering(Precipitation)(Q-P-T) Process for Ultra-high Strength Steel

Microstructure and Mechanical Properties of A Nb-Microalloyed Medium Carbon Steel Treated by Quenching-Partitioning Process