Abstract:Strut-based lattice structures (SLSs) have been widely used in modern industries including aerospace, automobile and biological implant, due to their unique properties such as lightweight, good energy absorption capability and high specific strength. However, the obtainable mechanical performance is significantly limited by the monotonous strut-based feature without any reinforcement topology. The inherent strengthening mechanisms and atom-scale models in material science may be crucial and valuable to optimize the complex structures with desired properties. Inspired by the solid solution strengthening mechanisms in crystal microstructure, a series of novel crystal-inspired hybrid structures, i.e., the common face-center cubic with Z-strut (FCCZ) structure, the face-center substitutional lattice (FCSL) structure, the edge-center interstitial lattice (ECIL) structure and the vertex-node substitutional lattice (VNSL) structure were designed and fabricated by laser powder bed fusion (LPBF) additive manufacturing in this work. The effect of node location on the LPBF formability, mechanical performance, stress distribution, deformation modes and failure mechanisms of the crystal-inspired components was systematically investigated. The computational fluid dynamics (CFD) method was used to understand the dynamics of molten pool to reveal the formation mechanism and control methods of the dross defect attached to overhanging surfaces. Finite element model (FEM) was established to show the stress distribution and deformation behavior of these hybrid structures during compression. Results showed that the ECIL structure possessed the highest specific energy absorption ( SEA ) of 13.7 J/g, which increased by 17% compared with the initial FCCZ structure. The crush force efficiency ( CFE ) of VNSL structure reached the peak value of 66% with a unique axisymmetric shear band during deformation, which increased by 14% compared to the FCCZ structure. The underlying mechanism analysis revealed that the as-designed spherical node could redistribute the stress and the performance of the lattice structures could be manipulated by tailoring the position of the spherical nodes. The present approach suggested that the hardening principles of crystalline materials could inspire the design of novel lattice structures with desired properties.

Si/SiC ceramic lattices with a triply periodic minimal surface structure prepared by laser powder bed fusion

Performance optimization of Si/SiC ceramic triply periodic minimal surface structures via laser powder bed fusion

Mechanical characteristics of Si/SiC graded ceramic lattice structures with a triply periodic minimal surface fabricated by laser powder bed fusion

Enhanced Molding and Mechanical Properties of SiC-based Ceramic Lattice Structures Via Digital Light Processing

POLYMER-DERIVED SIC CERAMIC WITH TRIPLY PERIOD MINIMAL SURFACE STRUCTURE FABRICATION THROUGH DIGITAL LIGHT PROCESSING

Study on the Fabrication and Mechanical Properties of SiC P /sic Gradient Lattice Structure Based on Selective Laser Sintering Technology

Controllable reduction of absorbance and two-step reaction for 3D-printed SiC ceramics with micron-level periodic structure

Effects of chopped carbon fiber on the forming, structure and mechanical properties of CCF/SiC composites fabricated by SLS and RMI

Complex SiC-based structures with high specific strength fabricated by vat photopolymerization and one-step pyrolysis

Stereolithography-based additive manufacturing of lightweight and high-strength Cf/SiC ceramics

Laser powder bed fusion of node-reinforced hybrid lattice structure inspired by crystal microstructure: Structural feature sensitivity and mechanical performance

Binder jetting additive manufacturing of hierarchical structural SiC w /SiC composites

Preparation of low residual silicon content Si-SiC ceramics by binder jetting additive manufacturing and liquid silicon infiltration

Mechanical properties and energy absorption of AlSi10Mg Gyroid lattice structures fabricated by selective laser melting

Ni–Ti multicell interlacing Gyroid lattice structures with ultra-high hyperelastic response fabricated by laser powder bed fusion

Improved Mechanical Properties and Energy Absorption of BCC Lattice Structures with Triply Periodic Minimal Surfaces Fabricated by SLM

Mechanical responses of sheet-based gyroid-type triply periodic minimal surface lattice structures fabricated using selective laser melting

Enhancing mechanical properties and damage tolerance of additive manufactured ceramic TPMS lattices by hybrid design

Fabrication of high-strength Si/SiC composites with low shrinkage rates via vat photopolymerization technology and liquid silicon infiltration

Single-step additive manufacturing of silicon carbide through laser-induced phase separation

A novel porous carbon synthesized to serve in the preparation of highly dense and high-strength SiC/SiC by reactive melt infiltration