Abstract:Bi2Te3-based materials are dominating thermoelectrics for almost all of the room-temperature applications. To meet the future demands, both their thermoelectric (TE) and mechanical properties need to be further improved, which are the requisite for efficient TE modules applied in areas such as reliable micro-cooling. The conventional zone melting (ZM) and powder metallurgy (PM) methods fall short in preparing Bi2Te3-based alloys, which have both a highly textured structure for high TE properties and a fine-grained microstructure for high mechanical properties. Herein, a mechanical exfoliation combined with spark plasma sintering (ME-SPS) method is developed to prepare Bi0.5Sb1.5Te3 with highly improved mechanical properties (correlated mainly to the dislocation networks), as well as significantly improved thermoelectric properties (correlated mainly to the texture structure). In the method, both the dislocation density and the orientation factor (F) can be tuned by the sintering pressure. At a sintering pressure of 20 MPa, an exceptional F of up to 0.8 is retained, leading to an excellent power factor of 4.8 mW m-1 K-2 that is much higher than that of the PM polycrystalline. Meanwhile, the method can readily induce high-density dislocations (up to ∼1010 cm-2), improving the mechanical properties and reducing the lattice thermal conductivity as compared to the ZM ingot. In the exfoliated and then sintered (20 MPa) sample, the figure-of-merit ZT = 1.2 (at 350 K), which has increased by about ∼20%, and the compressive strength has also increased by ∼20%, compared to those of the ZM ingot, respectively. These results demonstrate that the ME-SPS method is highly effective in preparing high-performance Bi2Te3-based alloys, which are critical for TE modules in commercial applications at near-room temperature.

Compositional engineering of metal-xanthate precursors toward (Bi 1− x Sb x ) 2 S 3 (0 ≤ x ≤ 0.05) films with enhanced room temperature thermoelectric performance

Large-area 2D bismuth antimonide with enhanced thermoelectric properties via multiscale electron-phonon decoupling

Enhanced Thermoelectric and Mechanical Performances in Sintered Bi0.48Sb1.52Te3-AgSbSe2 Composite.

Enhanced Thermoelectric and Mechanical Performances in Sintered Bi 0.48 Sb 1.52 Te 3 –AgSbSe 2 Composite

Synergistic Texturing and Bi/Sb‐Te Antisite Doping Secure High Thermoelectric Performance in Bi 0.5 Sb 1.5 Te 3 ‐Based Thin Films

Improving the thermoelectric performance of p-type (Bi x Sb 1− x ) 2 Te 3 thin films via tuning the Bi x Sb 1− x layer

In situ crystal-amorphous compositing inducing ultrahigh thermoelectric performance of p-type Bi0.5Sb1.5Te3 hybrid thin films

Leveraging the Cu 2 SnTe 3 additive for an improved thermoelectric figure of merit and module efficiency in Bi 0.5 Sb 1.5 Te 3 -based composites

Unraveling electronic origins for boosting thermoelectric performance of p-type (Bi,Sb) 2 Te 3

Synergistic Combination of Sb2Si2Te6 Additives for Enhanced Average ZT and Single-Leg Device Efficiency of Bi0.4Sb1.6Te3-based Composites

Silver-Based Intermetallic Heterostructures in Sb2Te3 Thick Films with Enhanced Thermoelectric Power Factors

Nanostructured Bi2-Xcuxs3 Bulk Materials With Enhanced Thermoelectric Performance

Integrating band engineering with point defect scattering for high thermoelectric performance in Bi2Si2Te6

Enhanced Thermoelectric Properties Obtained by Compositional Optimization in P -Type Bi X Sb 2− X Te 3 Fabricated by Mechanical Alloying and Spark Plasma Sintering

Highly Enhanced Thermoelectric and Mechanical Properties of Bi-Sb-Te Compounds by Carrier Modulation and Microstructure Adjustment

Enhancing the Thermoelectric and Mechanical Properties of Bi 0.5 Sb 1.5 Te 3 Modulated by the Texture and Dense Dislocation Networks

High performance of Mg3Bi1.5Sb0.5 based materials for power generation: Revealing the counter-intuitive effect of tuning Bi content on the thermoelectric properties

Improved thermoelectric and mechanical performance of Sb2Te3-based materials toward the segmented operation

Na/Bi-co-doping and Heterogeneous Interfaces Leading to Enhanced Thermoelectric Performance of P-Type Mg3Sb2-based Zintls

Effect of Composition Adjustment on the Thermoelectric Properties of Mg3Bi2-Based Thermoelectric Materials

Band Engineering Through Pb‐Doping of Nanocrystal Building Blocks to Enhance Thermoelectric Performance in Cu3SbSe4