Abstract:Scanning probe microscopy was used to simultaneously determine the molecular chain structure and intrinsic mechanical properties, including anisotropic elastic modulus and friction, for lamellae of highly oriented high-density polyethylene (HDPE) obtained by the melt-drawn method. The molecular-scale image of the highly oriented lamellae by friction force microscopy (FFM) clearly shows that the molecular chains are aligned parallel to the drawing direction, and the periodicities along and perpendicular to the drawing direction are 0.26 and 0.50 nm, respectively. The results indicate that the exposed planes of the lamellae resulting from the melt-drawn method are (200), which is consistent with results of transmission electron microscopy and electron diffraction. Because of the high degree of anisotropy in the sample, coming from alignment of the molecular chains along the drawing direction, the measured friction force, F, determined by FFM is strongly dependent on the angle, theta, between the scanning direction and the chain axis. The force increases as theta is increased from 0 degrees (i.e., parallel to the chain axis) to 90 degrees (i.e., perpendicular to the chain axis). The structural anisotropy was also found to strongly influence the measurements of the transverse chain modulus of the polymer by the nanoindentation technique. The measured value of 13.8 GPa with transverse modulus was larger than the value 4.3 GPa determined by wide-angle X-ray diffraction, which we attributed to anisotropic deformation of the lamellae during nanoindentation measurements that was not accounted for by the elastic treatment we adopted from Oliver and Pharr. The present approach using scanning probe microscopy has the advantage that direct correlations between the nanostructure, nanotribology, and nanomechanical properties of oriented samples can be determined simultaneously and simply.

Deformation induced changes in surface properties of polymers investigated by scanning force microscopy

Deformation Behavior of Microparticle-Based Polymer Films Visualized by AFM Equipped with a Stretching Device

Effects of stretching on crystalline phase structure and morphology of hard elastic PVDF fibers

Deformation Mechanisms of Polymer Thin Films by Simultaneous Kinetic Measurement of Microscopic Infrared Dichroism and Macroscopic Stress. Part Iii: Influence of Morphology on Molecular Orientation of Isotactic Polypropylene Films Subjected to Uniaxial Stretching

Segmental Orientations and Deformation Mechanism of Poly(Ether-Block-Amide) Films

Deformation Mechanisms of Polymer Thin Films by Simultaneous Kinetic Measurement of Microscopic Infrared Dichroism and Macroscopic Stress. 2. Molecular Orientation During Necking Process of Isotactic Polypropylene

Deformation and Molecular Orientation in Films of Metallocene Polypropylene, Ethylene-Butylene Rubber, and Their 80/20 (W/W) Blend Revealed by the Simultaneous Kinetic Measurement of Microscopic Infrared Dichroism, Macroscopic Stress, and Mesoscale Strain

Nanostructure and Mechanical Measurement of Highly Oriented Lamellae of Melt-Drawn HDPE by Scanning Probe Microscopy

Monitoring Nanoscale Deformations in a Drawn Polymer Melt with Single-Molecule Fluorescence Polarization Microscopy

Dual Ratiometric Fluorescence Monitoring of Mechanical Polymer Chain Stretching and Subsequent Strain-Induced Crystallization

Deformation of polymer films by bending forces

Plastic deformation of the microfibrils in wet polyacrylonitrile fibers induced by the stretching field

Micro-SAXS and force/strain measurements during the tensile deformation of single struts of an elastomeric polyurethane foam.

In-situ force microscopy to investigate fracture in stretchable electronics: insights on local surface mechanics and conductivity

Effects of stretching on the frictional stress of rubber

Effect of the Molecular Weight on Deformation States of the Polystyrene Film by AFM Single Scanning.

Deformation Mechanism of Hard Elastic Polyethylene Film During Uniaxial Stretching: Effect of Stretching Speed

Multiscale characterization of interfacial region in flexible rubber composites: initial structure and evolution upon thermal treatment

Tracking the evolution of the morphology and stress distribution of SIS thermoplastic elastomers under tension using atomic force microscopy

Analysis of Surface Mechanical Properties of Polymer Blend Ultrathin Films by Scanning Force Microscopy

Nanoscale rheology: Dynamic Mechanical Analysis over a broad and continuous frequency range using Photothermal Actuation Atomic Force Microscopy