Abstract:Ultra-high nickel single-crystal cathode materials have become the most promising for lithium-ion batteries. However, the preparation of ultra-high nickel single-crystal precursors by a continuous coprecipitation method has the disadvantages of large particle size, wide distribution, poor morphology. The extent of the inhomogeneous reactions can be more severe in single-crystal cathodes with larger particle size. Herein, the coprecipitation method with a solid concentrator was adopted, and citrate sodium was used as a complexing agent to improve the physical properties of precursors and electrochemical performance of single-crystal cathode materials. By analyzing the morphology and agglomeration mechanism of the precursor nucleuses under different pH values, it was found that hexagonal nanosheets grew along the 101 direction, and the primary particles showed thicker at pH of 11.4. The hexagonal nanosheets grew along the 001 direction, and the primary particles showed finer at pH of 12.2. The morphology and particle size uniformity of the secondary particles formed by agglomeration at these two pH values showed poor. However, hexagonal nanosheets grew synergistically along the 001 and 101 directions at pH of 11.8, so the primary particles with uniform particle size gradually agglomerated, and then the secondary particles with ultra-small particle size and uniform distribution obtained. Compared to materials prepared by the traditional continuous coprecipitation method, the precursor displays a smaller particle size(D50 = 1.8 µm), higher sphericity, uniformity and denser internal structure. In order to evaluate the performance of Ni0.94Co0.04Mn0.02(OH)2 with ultra-small particle size, the sintering conditions of LiNi0.94Co0.04Mn0.02O2 need to be explored. It was found that the LiNi0.94Co0.04Mn0.02O2 cathode material prepared at 790 °C exhibited higher discharge capacity, cycle and rate performance, compared to materials prepared at 760 °C and 820 °C. We further utilized TEM, EPMA, and XPS to test the internal structure and valence state of LiNi0.94Co0.04Mn0.02O2 cathode material. The results show that the LiNi0.94Co0.04Mn0.02O2 calcined at 790 °C has a good single crystal structure. The LiNi0.94Co0.04Mn0.02O2 cathode materials inherited the structure and particle size of Ni0.94Co0.04Mn0.02(OH)2 precursors, and displayed discharge capacity of 194.7 mAh/g and capacity retention rate of 89.8 % after 100 cycles at 1 C. The microstructure and phase transition of the as-prepared cathode material are well-maintained after long-term cycling, without obvious inter-crystalline micro-crack. The results indicate that its electrochemical performance is better than that of cathode materials with precursors prepared by a continuous coprecipitation method. This work provides new insights for the preparation of small-particle-size precursor and single-crystal cathode materials.

A green and economical route to the precursor for the synthesis of single crystal LiNi0.5Co0.2Mn0.3O2

Ton-scale preparation of single-crystal Ni-rich ternary cathode materials for high-performance lithium ion batteries

Insight of Synthesis of Single Crystal Ni‐Rich LiNi1−x−yCoxMnyO2 Cathodes

A short process and low-cost preparation of single crystal LiNi0.6Co0.2Mn0.2O2 cathode for lithium-ion batteries

Application of precursor with ultra-small particle size and uniform particle distribution for ultra-high nickel single-crystal cathode materials by coprecipitation method

Synthesis of Single-Crystal LiNi 0.7 Co 0.15 Mn 0.15 O 2 Materials for Li-Ion Batteries by a Sol–Gel Method

One-Step Synthesis of a Single-Crystal LiNi 0.83 Co 0.11 Mn 0.06 O 2 Cathode with Excellent Electrochemical Properties by Ti 4+ Doping and LiTi 2 O 4 In Situ Chemical Coating Using a Novel Variable Temperature Sintering Process

A simple one-step molten salt method for synthesis of micron-sized single primary particle LiNi0.8Co0.1Mn0.1O2 cathode material for lithium-ion batteries

Solid-state approach for synthesizing single crystal LiNi0.8Co0.1Mn0.1O2 cathode of lithium-ion batteries

One‐Step Molten‐Salt‐Assisted Approach for Direct Preparation and Regeneration of LiNi0.6Co0.2Mn0.2O2 Cathode

Low-temperature strategy to synthesize single-crystal LiNi0.8Co0.1Mn0.1O2 with enhanced cycling performances as cathode material for lithium-ion batteries

Synthesis of Monodisperse and Discrete Ultra-High Nickel LiNi0.97Co0.02Mn0.01O2 Octahedral Single Crystals via Single Crystal Intermediates for Li-Ion Batteries

Enhanced Electrochemical Performance of LiNi0.6Co0.2Mn0.2O2 Cathode Materials by Ultrasonic-Assisted Co-Precipitation Method

Synthesis of cathode material LiNi_(1/3)Co_(1/3)Mn_(1/3)O_2 and its electrochemical performances

Oxalate Co-Precipitation Synthesis of LiNi0.6Co0.2Mn0.2O2 for Low-Cost and High-Energy Lithium-Ion Batteries

Single-Crystal LiNi0.6Co0.2Mn0.2O2: Facile Preparation and Electrochemical Performance

Synthesis of single-crystal LiNi0.8Co0.1Mn0.1O2 materials for Li-ion batteries by microfluidic technology

(Invited) Delineating the Intricacies Involved in the Synthesis of Cobalt-Free High-Nickel Layered Oxide Cathodes for Lithium-Ion Batteries

Green Synthesis of High-Performance Li1.2Mn0.6Ni0.2O2 with the Assist of a Microreactor

Introducing an Efficient and Eco-Friendly Spray-Drying Process for the Synthesis of NCM Precursor for Lithium-ion Batteries

Temperature-controlled direct dry synthesis of Co-Ni free cathode materials 0.7Li2MnO3·0.3LiFeO2 for lithium-ion batteries