Abstract:Modern civilization and cutting-edge technologies and tools are highly dependent on energy storage devices and demand efficient and long-lasting high-energy-density storage devices. Lithium metal batteries have surpassed their competitors concerning energy density due to their inherent high specific capacity (3860 mAh/g) and the lowest electrochemical potential (-3.04 V vs. standard hydrogen electrode), proving to be one of the most favorable energy storage devices for smart and mobile gadgets, electric automobiles, grid storage, etc. However, safety-threatening and performance-decay challenges associated with lithium metal anodes, such as lithium dendrite formation, uncontrolled parasitic reactions between Li-metal and electrolyte, low coulombic efficiency, dead Li-formation, etc., restrict its employment in practical batteries. The root cause of the dendrite formation is poor Li-ion conductivity of bulk lithium metal, which results in an uneven electric field distribution, leading to non-uniform Li deposition/stripping upon repeated charge/discharge. Herein, a facile chemical reduction process is being opted to fabricate a highly Li-ion diffusive Li-Sn-based artificial SEI layer on the lithium metal surface to prevail over the above-mentioned issues. Therefore, upon careful concentration investigation of reactants, 25 mM precursor concentration (SnCl 4 in EC: DMC in 1:1 volume ration) demonstrated the best electrochemical performance, revealing a cumulative capacity of over 700 mAh/cm 2 at a current density of 1 mA/cm 2 for 1 h in a symmetric cell. Physical characterizations (XRD and SEM-EDS) showed a thin layer containing Li-Sn alloys along with LiCl formed at the lithium metal surface. Possessing high Li-ion diffusivity, Li-Sn alloyed hybrid anode illustrated a gradual decrease in the charge transfer resistance on increasing the concentration, thus, lower overpotential in symmetric cells, in contrast to pristine Li-metal. However, an increase in the electrical resistance has been observed on increasing the precursor concentration due to the presence of the insulating LiCl phase in the protective layer. Moreover, in-situ optical microscopy demonstrated more uniform and on-surface Li-deposition for the hybrid electrode, whereas mossy and dendritic growth on bare Li-metal. Full cells prepared with Li-Sn alloyed anode against NMC532 cathode illustrated stable cycling up to 150 cycles; contrastingly, the cell with pristine Li-metal showed a drastic capacity fade just after 100 cycles, demonstrating the inclination towards safer lithium metal batteries.

Li-Alloy texture creates in-built Li(110) epitaxy in a thin Li-metal anode allowing high depth-of-discharge cycling in carbonate electrolyte

Dynamic Concentration of Alloying Element on Anode Surface Enabling Cycle‐Stable Li Metal Batteries

Enabling Isotropic Li Growth Via Li Foil Facet-Engineering for High-Performance Li Metal Batteries

Favorable Interfacial Chemomechanics Enables Stable Cycling of High-Li-Content Li–In/Sn Anodes in Sulfide Electrolyte-Based Solid-State Batteries

Steady cycling of lithium metal anode enabled by alloying Sn-modified carbon nanofibers

Realizing Ultrathin LiSn Alloy Anode by Tuning the Wettability of Molten Li for High-Energy-Density Batteries

Li plating on alloy with superior electro-mechanical stability for high energy density anode-free batteries

Li-Sn Alloyed Layer Containing Artificial SEI on Li-Metal Anode for Superior Lithium Metal Batteries: Development and Understanding of Anode/Electrolyte Interfacial Phenomena

Stabilizing Lithium Metal Anode by Molecular Beam Epitaxy Grown Uniform and Ultrathin Bismuth Film

In-situ constructed polymer/alloy composite with high ionic conductivity as an artificial solid electrolyte interphase to stabilize lithium metal anode

Long-term stable Li metal anode enabled by strengthened and protected lithiophilic LiZn alloys

Favorable Interfacial Chemomechanics Enables Stable Cycling of High Li-Content Li-In/Sn Anodes in Sulfide Electrolyte Based Solid-State Batteries

Stable lithium metal anode enabled by lithium metal partial alloying

Strong Texturing of Lithium Metal in Batteries

Li–Zn Overlayer to Facilitate Uniform Lithium Deposition for Lithium Metal Batteries

Single‐Crystalline LiMg Alloy Anode for Deep Cycling All Solid State Lithium Metal Batteries

Li (200) with in-situ generated high entropy alloy/oxide fillers and Li 2 O enabling desirable Li metal anode

Electronic Localization Derived Excellent Stability of Li Metal Anode with Ultrathin Alloy

Optimal Interfacial Model between the Alloy Surface and Electrolyte Solvation Structure for a Stable Lithium Metal Electrode

3D Porous and Li-rich Sn–Li Alloy Scaffold with Mixed Ionic-Electronic Conductivity for Dendrite-Free Lithium Metal Anodes

Advancing Anode-Less Lithium Metal Batteries: ZnF2 Modification and In-Situ Structural Regulation for Enhanced Performance