Electrolyte-assisted low-voltage decomposition of Li 2 C 2 O 4 for efficient cathode pre-lithiation in lithium-ion batteries

Rang Xiao,Cong Kang,Yang Ren,Jiyuan Jian,Binghan Cui,Geping Yin,Yulin Ma,Pengjian Zuo,Guokang Han,Chunyu Du

DOI: https://doi.org/10.1039/d3cc04442d

IF: 4.9

2023-01-01

Chemical Communications

Abstract:A NaNO 2 -catalyzed strategy is proposed for cathode pre-lithiation with Li 2 C 2 O 4 .

chemistry, multidisciplinary

What problem does this paper attempt to address?

NaNO2 additive-assisted Li2O2 decomposition for highly efficient cathode prelithiation of lithium-ion batteries

Rang Xiao,Cong Kang,Yang Ren,Renlong Li,Jiyuan Jian,Binghan Cui,Geping Yin,Xinqun Cheng,Yulin Ma,Hua Huo,Pengjian Zuo,Guokang Han,Chunyu Du

DOI: https://doi.org/10.1016/j.cej.2023.145710

IF: 15.1

2023-08-01

Chemical Engineering Journal

Abstract:Silicon based anodes are the most attractive candidates for high energy density lithium-ion batteries (LIBs), but their practical applications are hindered by the large initial lithium loss. Cathode prelithiation is an effective method to mitigate the active lithium loss in silicon-based LIBs. However, a cathode prelithiation method enabling suitable cutoff voltage and less residues still remains challenging. Herein, we demonstrate that soluble additive NaNO2 in carbonate-based electrolyte could efficiently reduce the decomposition voltage of Li2O2 to as low as 4.3 V. The liquid–solid synergistic effect of NaNO2 additive and LiNi0.83Co0.07Mn0.1O2 (NCM) cathode on the Li2O2 decomposition is revealed, which enables the highly efficient cathode prelithiation with remarkable Li2O2 decomposition efficiency of 96.7% at the acceptable cutoff voltage 4.4 V. For the addition for 1 wt% Li2O2, a capacity of 14.85 mAh/g could be supplied in the first charge. Besides, NaNO2 could reduce the active lithium loss during the following cycles for its irreversibly decomposing into Li3N and LiNxOy on the anode surface. The full cell assembled with NCM(Li2O2) cathode and silicon-graphite (Si-G) anode delivers 17.3% higher initial specific capacity (218.6 mAh/g) than that without Li2O2 (186.4 mAh/g) at the charge cutoff voltage of 4.4 V. This work provides a novel electrolyte-assisted cathode prelithiation strategy to compensate the initial active lithium loss, which is highly compatible with the current battery fabrication process.

engineering, chemical, environmental
Non-destructive Chemical Prelithiation of VO2(B) Anodes Constructing a Multifunctional Interphase Layer for Advanced Li-Ion Batteries

Bo Yan,Changqing Xu,Luzhi Liu,Fei Wang,Wei Xiao,Lulu Zhang,Xuelin Yang,Xifei Li,Renheng Wang

DOI: https://doi.org/10.1016/j.cej.2024.151185

IF: 15.1

2024-01-01

Chemical Engineering Journal

Abstract:VO2(B) stands as a promising anode material, comparable to the disordered rock-salt phase Li3+xV2O5, owning to its ease of preparation, suitable redox potential, and remarkable rate capability. However, the practical application of VO2(B) anodes faces substantial limitations due to its low initial coulombic efficiency (ICE) and instability of solid electrolyte interface (SEI) layer during cycling. In this study, we introduce a highly efficient, controllable, and non-destructive chemical prelithiation method utilizing a reductive Li-arene reagent, formed by dissolving Li-metal to THF solutions containing biphenyl derivatives. This method enables the VO2(B) anode to achieve an ICE of nearly 100 %. The investigation on the chemical composition and mechanical properties of SEI layers reveals that the prelithiated VO2(B) electrode contains a more favorable LiF component, fewer adverse byproducts, and exhibits a thinner thickness with high structural strength. Kinetic analysis demonstrates that the prelithiation treatment accelerates the diffusion of lithium ions, reduces interfacial reaction resistances, and maintains interface stability during cycling. To demonstrate the practical application, we assemble a well-designed Prelithiation VO2(B)||NCM811 full cell, achieving an enhancement in the energy density of at least 20 %. This work underscores the potential of prelithiated VO2(B) electrodes for developing lithium-ion batteries (LIBs) with high-safety and high-energy/power density.
Mo2C catalyzed low-voltage prelithiation using nano-Li2C2O4 for high-energy lithium-ion batteries

Wei Zhong,Ce Zhang,Siwu Li,Wei Zhang,Ziqi Zeng,Shijie Cheng,Jia Xie

DOI: https://doi.org/10.1007/s40843-022-2235-4

2022-11-25

Science China Materials

Abstract:Irreversible lithium loss in the initial cycles appreciably reduces the energy density of lithium-ion batteries. Prelithiation is an effective way to compensate for such lithium loss, but current methods suffer from either the instability or low capacity of prelithiation reagents. Lithium oxalate (Li 2 C 2 O 4 ) has shown great potential as a lithium-compensation material because of its high theoretical capacity (equivalent to lithium metal), low cost, and air stability. However, the practical applications of Li 2 C 2 O 4 are limited by its low electrochemical activity and high critical decomposition voltage. In this study, we performed the prelithiation of a low-voltage cathode by using Mo 2 C catalysis and nano-Li 2 C 2 O 4 . Results show that the Mo 2 C catalyst changes the electron cloud distribution around Li 2 C 2 O 4 and greatly reduces the activation energy, thereby significantly accelerating the lithium release from Li 2 C 2 O 4 . The nano-Li 2 C 2 O 4 prepared by freeze-drying shows accelerated ionic and electronic conduction as well as close contact with Mo 2 C. Benefiting from the synergistic effect, the decomposition potential of Li 2 C 2 O 4 is decreased by 0.5 V with an efficiency close to 100%. The LiCoO 2 ∥SiO full cell empowered with the nano-Li 2 C 2 O 4 /Mo 2 C prelithiation composite demonstrates 46.9% higher capacity than the control and thus has great potential for practical applications.

materials science, multidisciplinary
Hierarchical spherical Mo2C/N-doped graphene catalyst facilitates low-voltage Li2C2O4 prelithiation

Wei Zhong,Siwu Li,Mengchuang Liu,Qiang Wu,Ziqi Zeng,Shijie Cheng,Jia Xie

DOI: https://doi.org/10.1016/j.nanoen.2023.108757

IF: 17.6

2023-10-01

Nano Energy

Abstract:The self-sacrificing Li2C2O4 is a promising lithium replenisher benefiting from its high specific capacity, residue-free and low-cost properties. However, the intrinsic low electrochemical activity leads to a decomposition potential up to 4.7 V, posing a challenge for the compatibility of electrolyte and cathode materials. Herein, a three-dimensional (3D) hierarchical spherical Mo2C/N-doped graphene co-catalysts is synthesized by self-polymerization and high-temperature annealing. It is shown that the synergistic catalytic effect of Mo2C and N-doped activated graphene enhances the reactivity of Li2C2O4 and the hierarchical three-dimensional conducting network accelerates the electron-ion transport. When the nano-Li2C2O4 is homogeneously encapsulated in the spherical catalytic center using a freeze-drying technique, the electrochemical reaction of Li2C2O4 is greatly promoted, resulting a significant drop of decomposition potential from 4.7 V to 4.16 V. As a result, the specific capacity of Gr||LFP and SiC||LFP full cells with composite lithium replenisher can be increased by 15% and 22%, respectively. Moreover, the solid electrolyte interface (SEI) is appropriately strengthened with pre-lithiation and thus guarantees superior cycling performance.

materials science, multidisciplinary,chemistry, physical,physics, applied,nanoscience & nanotechnology
Scalable spray-dried high-capacity MoC1-x/NC-Li2C2O4 prelithiation composite for lithium-ion batteries

Wei Zhong,Qiang Wu,Yuanke Wu,Renjie He,Cong Liao,Shijie Cheng,Jia Xie

DOI: https://doi.org/10.1016/j.ensm.2024.103318

IF: 20.4

2024-03-01

Energy Storage Materials

Abstract:Li2C2O4 is recognized as a promising prelithiation reagent for compensating active lithium owing to its residue-free, high-capacity, air-stable and cost-effective advantages. However, the inherent challenges of low conductivity and high reaction energy barriers necessitate the incorporation of a catalyst to expedite charge conduction and enhance electrochemical activity. It is essential to achieve an efficient composite Li2C2O4 with the catalyst while maintaining substantial prelithiation capacity. Herein, a scalable spray-dried strategy is developed to fabricate MoC1-x/NC-Li2C2O4 composites. The defect-rich nano-MoC1-x/NC catalysis facilitates intimate contact with Li2C2O4, leading to the formation of homogeneous microspheres that promote efficient solid-solid catalysis. Remarkably, the specific capacity of MoC1-x/NC-Li2C2O4 can reach up to 1117 mAh g−1 (calculation based on the complete release of CO2) with a low ratio of catalysts, demonstrating significant application potential. Furthermore, the activation potential of homogeneous MoC1-x/NC-Li2C2O4 composite can be reduced to 4.12 V at 50°C, while maintaining favorable electrode integrity and wettability. Upon implementation in Gr||NCM622 and SiC||NCM622 full cell, the initial discharge specific capacity is improved by 10.5% and 11.6%, respectively. Notably, sufficient active lithium post-prelithiation preserves the cathode and SEI structural stability, ensuring a stable cycling performance. This work presents a scalable prelithiation material with great promise for advanced lithium-ion battery applications.

materials science, multidisciplinary,chemistry, physical,nanoscience & nanotechnology
Boosting the capability of Li2C2O4 as cathode pre-lithiation additive for lithium-ion batteries

Guxin Huang,Jianing Liang,Xingguo Zhong,Haoyue Liang,Can Cui,Cheng Zeng,Shuhao Wang,Mengyi Liao,Yue Shen,Tianyou Zhai,Ying Ma,Huiqiao Li

DOI: https://doi.org/10.1007/s12274-022-5146-0

IF: 9.9

2022-11-25

Nano Research

Abstract:Li 2 C 2 O 4 , with a high theoretical capacity of 525 mAh·g −1 and good air stability, is regarded as a more attractive cathode pre-lithiation additive in contrast to the reported typical inorganic pre-lithiation compounds which are quite air sensitive. However, its obtained capacity is much lower than the theoretical value and its delithiation potential (> 4.7 V) is too high to match with the most commercial cathode materials, which greatly impedes its practical application. Herein, we greatly improve the pre-lithiation performance of Li 2 C 2 O 4 as cathode additive with fulfilled capacity at a much-reduced delithiation voltage, enabling its wide applicability for typical commercial cathodes. We increase the capacity of Li 2 C 2 O 4 from 436 to 525 mAh·g −1 by reducing its particle size. Through optimizing the types of conductive additives, introducing nano-morphological NiO, MnO 2 , etc. as catalysts, and innovatively designing a bilayer electrode, the delithiation potential of Li 2 C 2 O 4 is successfully reduced from 4.778 to 4.288 V. We systematically study different particle size, conductive additives, and catalysts on the delithiation behavior of Li 2 C 2 O 4 . Finally, it is applied to pre-lithiate the hard carbon anode, and it is found that Li 2 C 2 O 4 could effectively increase the capacity of the full cell from 79.0 to 140.0 mAh·g −1 in the first cycle. In conclusion, our study proves that improving the reactivity is an effective strategy to boost the pre-lithiation of Li 2 C 2 O 4 .

materials science, multidisciplinary,chemistry, physical,physics, applied,nanoscience & nanotechnology
Non-destructive chemical prelithiation of VO 2 (B) anodes constructing a multifunctional interphase layer for advanced Li-Ion batteries

Bo Yan,Changqing Xu,Luzhi Liu,Fei Wang,Wei Xiao,Lulu Zhang,Xuelin Yang,Xifei Li,Renheng Wang

DOI: https://doi.org/10.1016/j.cej.2024.151185

IF: 15.1

2024-04-20

Chemical Engineering Journal

Abstract:VO 2 (B) stands as a promising anode material, comparable to the disordered rock-salt phase Li 3+x V 2 O 5 , owning to its ease of preparation, suitable redox potential, and remarkable rate capability. However, the practical application of VO 2 (B) anodes faces substantial limitations due to its low initial coulombic efficiency (ICE) and instability of solid electrolyte interface (SEI) layer during cycling. In this study, we introduce a highly efficient, controllable, and non-destructive chemical prelithiation method utilizing a reductive Li-arene reagent, formed by dissolving Li-metal to THF solutions containing biphenyl derivatives. This method enables the VO 2 (B) anode to achieve an ICE of nearly 100 %. The investigation on the chemical composition and mechanical properties of SEI layers reveals that the prelithiated VO 2 (B) electrode contains a more favorable LiF component, fewer adverse byproducts, and exhibits a thinner thickness with high structural strength. Kinetic analysis demonstrates that the prelithiation treatment accelerates the diffusion of lithium ions, reduces interfacial reaction resistances, and maintains interface stability during cycling. To demonstrate the practical application, we assemble a well-designed Prelithiation VO 2 (B)||NCM811 full cell, achieving an enhancement in the energy density of at least 20 %. This work underscores the potential of prelithiated VO 2 (B) electrodes for developing lithium-ion batteries (LIBs) with high-safety and high-energy/power density.

engineering, chemical, environmental
Sustainable Low-Temperature Coating of LATP/C Solid Electrolyte Composites on LiNi1/3Co1/3Mn1/3O2 Cathode Based on Lithium Iodide Solvent-Recrystallization for Li-Ion Batteries

tingting yang,Chi-Te Chin,Yingtuo Li,Ching-Hsiang Cheng

DOI: https://doi.org/10.1149/1945-7111/aca4a4

IF: 3.9

2022-11-22

Journal of The Electrochemical Society

Abstract:A mixed ionic (Li1.3Al0.3Ti1.7(PO4)3: LATP) and electronic conductor (porous carbon: C) hybrid layer can effectively enhance the electrochemical performance of cathode materials. In this work, a sustainable low-temperature synthesis strategy (≤ 200°C) combining ball milling and solvent-recrystallization of lithium iodide is proposed to prepare the LATP/C coated LiNi1/3Co1/3Mn1/3O2 (LNCMO) material. The characterizations of structures and morphology reveal that LATP and porous carbon powder are mixed into the ethanol dissolved lithium iodide by a simple ball milling process, then the lithium iodide is recrystallized to serve as a binder when ethanol is vaporized at a low temperature to coat uniform thickness and homogeneously distributed LATP/C on the surface of LNCMO cathode. The charge-discharge results illustrate that the cycling performance and rate discharge capability of the active materials coated with LATP/C are significantly superior to the bare LNCMO. AC impedance analysis confirms that lower charge transfer resistance and higher Li+ ion diffusion coefficient are achieved in cathode materials. This work successfully exploited a novel low-temperature cathode coating method based on lithium iodide solvent-recrystallization and obtained results comparable to high-temperature processes without suffering from side reaction problems.

electrochemistry,materials science, coatings & films
Catalytic Current Collector Design to Accelerate LiNO3 Decomposition for High‐Performing Lithium Metal Batteries

Qicheng Zhang,Lei Xu,Xinyang Yue,Jijiang Liu,Xin Wang,Xiaoya He,Zidan Shi,Shuzhang Niu,Wei Gao,Chun Cheng,Zheng Liang

DOI: https://doi.org/10.1002/aenm.202302620

IF: 27.8

2023-10-04

Advanced Energy Materials

Abstract:The reaction pathway for the LiNO3 decomposition is determined by investigating the LiNO3 evolution in an inner Helmholtz plane with various current collectors: a novel carbon foam@vanadium nitride (CF@VN) current collector and traditional current collectors (CF, Cu). Lithium nitrate is an attractive lithium additive in the construction of high‐performance lithium metal anodes with a Li3N‐rich solid electrolyte interphase (SEI) layer. However, the eight‐electron transfer process induces high energy barriers between LiNO3 and Li3N. Herein, the inner Helmholtz plane is tuned on a Li deposition host to attain sluggish/rapid LiNO3 decomposition kinetics, resulting in different intermediate content distributions of Li species in the SEI. Notably, lithium oxynitride (LiNO) is identified as the decomposition intermediate, and experimental and simulation results confirm its role in obstructing LiNO3 decomposition. Moreover, the results reveal that the dipole–dipole interaction between LiNO and the polar V≡N bond can change the ionic/covalent character of the N═O bonds, considerably facilitating the energy transfer process of the N═O cleavage, and promoting a LiNO3 reduction to achieve a Li3N‐rich SEI. Consequently, when the electrolyte contains 0.37 m LiNO3, dendrite, and dead Li formation are suppressed effectively with the VN system, and an average Coulombic efficiency of 99.7% over 1000 cycles (1 mA cm−2, 1 mAh cm−2) can be attained. These results can promote the nitride oxidation break process and pave the way for fabricating high‐performance Li3N‐rich lithium metal batteries.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,energy & fuels
Energy band modulation of Li2O-rGO core-shell as cathode sacrificial additive enables capacity enhancement of hard carbon anode in Li-ion batteries

Gang Liu,Zixuan Fang,Tingting Feng,Ming Zhang,Mengqiang Wu

DOI: https://doi.org/10.1016/j.jcis.2024.04.100

Abstract:Lithium oxides (Li2O) possess a considerable theoretical capacity, rendering them highly promising as cathodic pre-lithiation additives. However, its decomposition voltage exceeds the charging cut-off voltage of most cathode materials, hindering its direct use as a cathode sacrificial additive. Herein, we design a facile and safe method to reduce the decomposition energy of Li2O at room temperature to offset the irreversible capacity loss by using a core-shell structured Li2O-reduced graphene oxide (rGO)-polyethylene glycol (PEG) composite (denoted as Li2O-rGO-PEG). The graphene oxide (GO) was heat-treated to remove oxygen functional groups to synthesize rGO, and then reacted with Li2O to form a Li2O-rGO composite. According to the DFT calculations, the density of states at the Fermi level of Li2O-rGO becomes continuous and features a metallic nature, which significantly improves the electrical conductivity of Li2O and facilitates electron conduction that modify the delithiation potential of Li2O. PEG was used to enhance the cohesive force between rGO and Li2O and to protect Li2O from atmospheric contamination. Moreover, in order to demonstrate the excellent pre-lithiation ability of Li2O-rGO-PEG composite, hard carbon (HC) with low initial coulombic efficiency (ICE) was used as the anode. In the application of LFP (Li2O)/HC full cell, Li2O was decomposed to Li+ to effectively improve the initial charge capacity from 149.7 to 200 mAh/g and discharge capacity from 104.2 to 147.5 mAh/g, which are 33.6 % and 41.6 % higher than those of the pristine LFP/HC full cell, respectively. The cathode pre-lithiation method proposed in this work is simple and environmentally friendly. The successful utilization of Li2O as a pre-lithiation additive effectively addressed the issue of low initial coulombic efficiency of the HC, indicating excellent prospects for practical applications.
Harmless pre-lithiation via advantageous surface reconstruction in sacrificial cathode additives for lithium-ion batteries

Yulun Wu,Juanlang Guo,Furong Qin,Shihao Li,Naifeng Wen,Jingqiang Zheng,Wei Zhang,Huangxu Li,Zhian Zhang,Yanqing Lai

DOI: https://doi.org/10.1016/j.jcis.2023.12.141

2024-03-15

Abstract:Sacrificial cathode additives have emerged as a tempting strategy to compensate the initial capacity loss (ICL) in Li-ion batteries (LIBs) manufacturing. However, the utilization of sacrificial cathode additives inevitably brings residuals, side reactions, and negative impacts in which relevant researches are still in the early stage. In this study, we conduct a systematic investigation on the effects of employing a nickel-based sacrificial additive, Li2Cu0.1Ni0.9O2 (LCNO), and propose a feasible strategy to achieve advantageous surface reconstruction on LCNO. Specifically, we build a Li5AlO4 (LAO) coating layer on the LCNO through dry ball milling and annealing treatment. This process not only consumes surface residual lithium compounds on LCNO but also demonstrates minimal detrimental effects on its performance. The surface reconstructed LCNO (SR-LCNO) reveals mitigated gas generation and suppressed structure degradation under high working voltage (＞4.1 V), thereby causing negligible negative effects on the cycling capability and rate performance of commercial cathode materials. The full cells containing SR-LCNO deliver significantly improved electrochemical properties, with no observed exacerbation of side reactions. This work awakes the awareness of the prudent utilization of sacrificial cathode additives and provides an effective strategy for harmless pre-lithiation via surface reconstructed sacrificial cathode additives.
Exploiting Cation Intercalating Chemistry to Catalyze Conversion-Type Reactions in Batteries

Weiyuan Huang,Jimin Qiu,Yuchen Ji,Wenguang Zhao,Zihang Dong,Kai Yang,Ming Yang,Qindong Chen,Mingjian Zhang,Cong Lin,Kang Xu,Luyi Yang,Feng Pan

DOI: https://doi.org/10.1021/acsnano.2c11029

IF: 17.1

2023-03-11

ACS Nano

Abstract:Effective harvest of electrochemical energy from insulating compounds serves as the key to unlocking the potential capacity from many materials that otherwise could not be exploited for energy storage. Herein, an effective strategy is proposed by employing LiCoO(2), a widely commercialized positive electrode material in Li-ion batteries, as an efficient redox mediator to catalyze the decomposition of Na(2)CO(3) via an intercalating mechanism. Differing from traditional redox mediation processes...

materials science, multidisciplinary,chemistry, physical,nanoscience & nanotechnology
Enabling stable and high-rate cycling of a Ni-rich layered oxide cathode for lithium-ion batteries by modification with an artificial Li+-conducting cathode-electrolyte interphase

Shixuan Wang,Alvin Dai,Yuliang Cao,Hanxi Yang,Amine Khalil,Jun Lu,Hui Li,Xinping Ai

DOI: https://doi.org/10.1039/d1ta02563e

IF: 11.9

2021-01-01

Journal of Materials Chemistry A

Abstract:Ni-rich LiNi0.8Co0.1Mn0.1O2 (NCM811) cathodes are investigated to realize high energy density Li ion batteries for long life electric vehicle applications. However, capacity decay and thermal instability due to cathode-electrolyte interfacial degradation remain challenges that require sophisticated surface stabilization methods to address. Here, we propose a strategy, for the first time, to form an artificial Li+-conducting cathode-electrolyte interphase (ALCEI) on the NCM811 cathode surface using a nucleophilic reaction between polysulfides and vinylene carbonate (VC). The as-formed ALCEI layer simultaneously protects the NCM particles from electrolyte corrosion and facilitates Li+ ion transport, thus enabling stable and high rate cycling of NCM811. As a result, the ALCEI-modified NCM811 cathode exhibits a high capacity (211.6 mA h g(-1) at 0.1C), notable rate capability (134 mA h g(-1) at 10C), and superior cycle stability (94.2% over 200 cycles at 1C). These results underscore the use of interfacial engineering in high voltage cathode material development and provide a feasible strategy for stabilizing Ni-rich cathode interfaces in practical Li ion battery applications.
Lithiation-Induced Non-Noble Metal Nanoparticles for Li-O 2 Batteries.

Qingyu Yan

DOI: https://doi.org/10.1021/acsami.8b17417

IF: 9.5

2019-01-01

ACS Applied Materials & Interfaces

Abstract:Low-cost and highly active electrocatalysts are attractive for Li-O2 applications. Herein, a 3D interconnected plate architecture consisting of ultra-small Co-Ni grains embedded in lithium hydroxide nanoplates (Co2Ni@LiOH) is designed and prepared by a lithiation strategy at room temperature. This catalyst exhibits a remarkably reduced charge potential of ~ 3.4 V at 50 µA cm-2, which leads to the high roundtrip efficiency of ~ 79%, among the best levels reported and a cycle life of up to 40 cycles. The well-aligned network facilitates the oxygen diffusion and the electrolyte penetration into the electrode. The enhanced electrical conductivity network improves the charge transport kinetics and more active sites are exposed, which facilitate the adsorption and dissociation of oxygen during the oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) reactions. This new catalyst design inspires the development of effective non-noble metal catalyst for Li-O2 batteries.
Weakly solvated EC-free linear alkyl carbonate electrolytes for Ni-rich cathode in rechargeable lithium battery

Guohuang Kang,Geng Zhong,Jiabin Ma,Rui Yin,Kangning Cai,Tianqi Jia,Xiaolong Ren,Kuang Yu,Peiwu Qin,Zhen Chen,Feiyu Kang,Yidan Cao

DOI: https://doi.org/10.1016/j.isci.2022.105710

IF: 5.8

2022-12-01

iScience

Abstract:Ethylene carbonate (EC) in the electrolyte is not stable in cells operated at high voltage (≥4.4V) or with Li metal anode, which greatly reduce the energy density and lifetime of the rechargeable lithium battery. Herein, an EC-free linear alkyl carbonate-based electrolyte is developed, which enables the high-voltage (≥4.4V) and low-temperature (-30°C) application of Ni-rich cathode (LiNi0.8Mn0.1Co0.1O2, NCM811). The EC-free system, consisting of LiPF6 and LiNO3 in ternary linear alkyl carbonates, possesses low viscosity, weakly solvated structure, and high interfacial stability with both the Ni-rich cathode and the Li metal anode to avoid continuous electrode/electrolyte side reactions and metal dissolution from the cathode. As a result, the Li||NCM811 cell delivers remarkable capacity retention of 93 ± 0.5% at the voltage of 4.4V and 88 ± 0.6% at 4.5V over 100 cycles. This study provides very encouraging perspective to develop EC-free carbonate-based electrolyte for high-voltage and low-temperature application in high-energy-density rechargeable lithium batteries.

multidisciplinary sciences
The Electrolysis of Anti-Perovskite Li2 OHCl for Prelithiation of High-Energy-Density Batteries

Lulu Guo,Chen Xin,Jian Gao,Jianxun Zhu,Yiming Hu,Ying Zhang,Junpeng Li,Xiulin Fan,Yutao Li,Hong Li,Jieshan Qiu,Weidong Zhou

DOI: https://doi.org/10.1002/anie.202102605

2021-06-01

Abstract:Anti-perovskite type Li2 OHCl was previously studied as a solid-state Li+ conductor. Here, we report that the Li2 OHCl can be electrolyzed at 3.3 V or 4.0 V, with the creation of O2 /HCl gases and the release of 2 equiv. Li+ via two different decomposition routes, depending on the acidity of electrolyte. In the electrolyte with trace acid, the Li2 OHCl is oxidized at a constant voltage of 3.3 V. In neutral electrolyte, the oxidization of Li2 OHCl starts at 4.0 V, but the produced HCl will increase the acidity of electrolyte and lead to a voltage drop to 3.3 V for the electrolysis of Li2 OHCl. The electrolysis of Li2 OHCl delivers a lithium releasing capacity as high as 810 mAh g-1 , with an equivalent Li-deposition or Li-intercalation on anode, making it a promising candidate as a Li reservoir for prelithiation of anode. Using Li2 OHCl as the lithium source, silicon-carbon (Si@C) composite anode can be effectively prelithiated. The full cells composed of LiNi0.8 Mn0.1 Co0.1 O2 (NMC811) cathode and prelithiated Si@C anode exhibited increased capacities with the increment of prelithiation dosages.
Simultaneous double membrane electrolysis of sodium sulfate solution and preparation of hydroxide precursor for layered cathode materials

Songlin Liu,Zhixing Wang,Ding Wang,Huajun Guo,Guochun Yan,Guangchao Li,Wenjie Peng,Xinhai Li,Jiexi Wang

DOI: https://doi.org/10.1016/j.jclepro.2023.139272

IF: 11.1

2023-10-22

Journal of Cleaner Production

Abstract:In this paper, a material-oriented metallurgical electrolysis strategy, which is of such characteristics as short process, easy procedure, and nonpollution, is proposed to treat sodium sulfate wastewater and simultaneously prepare high value-added cathode material LiNi 1/3 Co 1/3 Mn 1/3 O 2 for lithium-ion batteries. The strategy is divided into two parts. First, the Ni 1/3 Co 1/3 Mn 1/3 (OH) 2 precursor is obtained by double membrane electrolyzing a mixed solution of Na 2 SO 4 , NiSO 4 , CoSO 4 , and MnSO 4 under the optimum electrolysis conditions (60 °C, 1.0 A). Furthermore, LiNi 1/3 Co 1/3 Mn 1/3 O 2 cathode is obtained through solid-sintering desulfurization. The change of sulfur content in the process and its effect on the morphology and electrochemical properties of the materials are investigated. Under optimum desulfurization conditions, the LiNi 1/3 Co 1/3 Mn 1/3 O 2 electrode delivers a high initial specific discharge capacity of 195.0 mAh·g −1 and a satisfying capacity retention of 85.0% after 120 cycles at 0.1 C in 2.5–4.5 V. This innovative strategy can realize the comprehensive utilization of sodium sulfate wastewater for preparation of Ni, Co, Mn-contained layered cathode materials.

environmental sciences,green & sustainable science & technology,engineering, environmental
Achieving Stable Anionic Redox Chemistry in Li-excess O2-type Layered Oxide Cathode Via Chemical Ion-Exchange Strategy

Xin Cao,Haifeng Li,Yu Qiao,Min Jia,Ping He,Jordi Cabana,Haoshen Zhou

DOI: https://doi.org/10.1016/j.ensm.2021.02.047

IF: 20.4

2021-01-01

Energy Storage Materials

Abstract:Triggering oxygen redox activity has been regarded as a promising strategy to boost the output capacity of cathode materials for Li/Na-ion batteries. However, irreversible loss of lattice oxygen aggravates a structural distortion to a spinel phase, which leads to severe voltage decay and capacity degeneration. Herein, via chemical ion exchange procedure, the sodium within the alkali metal layer of a P2-type oxide precursor has been substituted by Li while the transition metal layer can be well preserved, resulting in the formation of a Li-excess O2-type layered oxide cathode, Li-0.66[Li0.12Ni0.15Mn0.73]O-2. Through systematic in/ex-situ and surface/bulk characterization (hard X-ray absorption spectroscopy, operando Raman/XRD and differential electrochemical mass spectroscopy, etc.), the redox reversibility and structural stability has been comprehensively demonstrated. Moreover, being evolved from the same sodium-based precursor, a similar O2-type compound generated by electrochemical ion exchange procedure presents severely irreversible behavior on both structural and redox processes. These findings elucidated that the chemical ion exchange strategy can be regarded as an efficient way to design high- capacity cathode candidates possessing stable anionic/cationic redox activities and enhanced structural stability.
A Molten-Salt Method to Synthesize Ultrahigh-Nickel Single-Crystalline LiNi0.92 Co0.06 Mn0.02 O2 with Superior Electrochemical Performance as Cathode Material for Lithium-Ion Batteries.

Mengtao Wu,Yimin Zhang,Yuzong Gu,Fei Lv

DOI: https://doi.org/10.1002/smll.202201946

IF: 13.3

2022-06-14

Small

Abstract:Ni-rich layered oxides have been intensively considered as promising cathode materials for next-generation Li-ion batteries. Nevertheless, the performance degradation caused by intergranular cracks and electrode/electrolyte interface parasitic reactions restricts their further application. Compared with secondary particles, single-crystal (SC) materials have better mechanical integrity and cycling stability. However, the preparation of ultrahigh-nickel layered SC cathode still remains a serious challenge. Herein, a novel LiOH-LiNO3 -H3 BO3 molten-salt method is proposed to synthesize SC LiNi0.92 Co0.06 Mn0.02 O2 with considerable crystallinity and uniformity. The critical impacts of calcination temperature and boric acid on the microstructure and electrochemical property of Ni-rich layered oxides are systematically investigated. The results show that the crystal growth is promoted and the stability of crystal structure is improved by this synthesis method. In particular, the optimal electrode demonstrates a superior initial discharge capacity of 214.8 mAh g-1 with a high capacity retention of 86.3% over 300 cycles as tested by pouch-type full cells at 45 ºC. This work not only prepares an ultrahigh-nickel layered CS cathode with superior electrochemical performances, but also provides a feasible method for the synthesis of other CS layered cathode materials.

Medicine,Materials Science,Engineering,Chemistry
In-situ Encapsulation of Nanoscale Er2O3 Phase to Drastically Suppress Voltage Fading and Capacity Degradation of Li- and Mn-rich Layered Oxide Cathode for Lithium-Ion Batteries.

Shiming Zhang,Haitao Gu,Tian Tang,Wubin Du,Mingxia Gao,Yongfeng Liu,Dechao Jian,Hongge Pan

DOI: https://doi.org/10.1021/acsami.7b09002

IF: 9.5

2017-01-01

ACS Applied Materials & Interfaces

Abstract:A novel strategy of in-situ precipitation and encapsulation of Er2O3 phase on Li(Li0.2Ni0.13Co0.13Mn0.54)O2 (LNCMO) cathode material for lithium-ion batteries is proposed for the first time. The Er2O3 phase is precipitated from the bulk of the LNCMO material and encapsulated onto its entire surface during calcining process. Electrochemicial performance is investigated by a galvanostatic charge and discharge test. Structure and morphology are characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electronic microscopy (SEM) and high-resolution transmission electron microscopy (HRTEM). Results show that an about 10 nm Er2O3 layer is successfully encapsulated onto the entire surface of the LNCMO matrix material. This unique nanoscale Er2O3 encapsulation can significantly prevent the LNCMO cathode material to be corroded by electrolyte and stabilize the crystal structure of the LNCMO cathode during cycling. Therefore, the prepared Er2O3 coated LNCMO composite exhibits excellent cycling performace and high initial coulombic efficiency.

Electrolyte-assisted low-voltage decomposition of Li 2 C 2 O 4 for efficient cathode pre-lithiation in lithium-ion batteries

NaNO2 additive-assisted Li2O2 decomposition for highly efficient cathode prelithiation of lithium-ion batteries

Non-destructive Chemical Prelithiation of VO2(B) Anodes Constructing a Multifunctional Interphase Layer for Advanced Li-Ion Batteries

Mo2C catalyzed low-voltage prelithiation using nano-Li2C2O4 for high-energy lithium-ion batteries

Hierarchical spherical Mo2C/N-doped graphene catalyst facilitates low-voltage Li2C2O4 prelithiation

Scalable spray-dried high-capacity MoC1-x/NC-Li2C2O4 prelithiation composite for lithium-ion batteries

Boosting the capability of Li2C2O4 as cathode pre-lithiation additive for lithium-ion batteries

Non-destructive chemical prelithiation of VO 2 (B) anodes constructing a multifunctional interphase layer for advanced Li-Ion batteries

Sustainable Low-Temperature Coating of LATP/C Solid Electrolyte Composites on LiNi1/3Co1/3Mn1/3O2 Cathode Based on Lithium Iodide Solvent-Recrystallization for Li-Ion Batteries

Catalytic Current Collector Design to Accelerate LiNO3 Decomposition for High‐Performing Lithium Metal Batteries

Energy band modulation of Li2O-rGO core-shell as cathode sacrificial additive enables capacity enhancement of hard carbon anode in Li-ion batteries

Harmless pre-lithiation via advantageous surface reconstruction in sacrificial cathode additives for lithium-ion batteries

Exploiting Cation Intercalating Chemistry to Catalyze Conversion-Type Reactions in Batteries

Enabling stable and high-rate cycling of a Ni-rich layered oxide cathode for lithium-ion batteries by modification with an artificial Li<SUP>+</SUP>-conducting cathode-electrolyte interphase

Lithiation-Induced Non-Noble Metal Nanoparticles for Li-O 2 Batteries.

Weakly solvated EC-free linear alkyl carbonate electrolytes for Ni-rich cathode in rechargeable lithium battery

The Electrolysis of Anti-Perovskite Li2 OHCl for Prelithiation of High-Energy-Density Batteries

Simultaneous double membrane electrolysis of sodium sulfate solution and preparation of hydroxide precursor for layered cathode materials

Achieving Stable Anionic Redox Chemistry in Li-excess O2-type Layered Oxide Cathode Via Chemical Ion-Exchange Strategy

A Molten-Salt Method to Synthesize Ultrahigh-Nickel Single-Crystalline LiNi0.92 Co0.06 Mn0.02 O2 with Superior Electrochemical Performance as Cathode Material for Lithium-Ion Batteries.

In-situ Encapsulation of Nanoscale Er2O3 Phase to Drastically Suppress Voltage Fading and Capacity Degradation of Li- and Mn-rich Layered Oxide Cathode for Lithium-Ion Batteries.