Abstract:A lattice‐matched MTO coating has successfully been built on ultrahigh single‐crystal LiNi0.9Co0.05Mn0.05O2 particle by a neoteric in situ chemical reaction process, which can not only relieve lattice strain by avoiding inhomogeneity of the Li‐ion concentration, but also suppress cation mixing and irreversible oxygen loss for ensuring the smooth transportation of Li‐ion, thus preventing planar gliding and delamination cracking along the sliding planes. Planar gliding along with anisotropic lattice strain of single‐crystalline nickel‐rich cathodes (SCNRC) at highly delithiated states will induce severe delamination cracking that seriously deteriorates LIBs' cyclability. To address these issues, a novel lattice‐matched MgTiO3 (MTO) layer, which exhibits same lattice structure as Ni‐rich cathodes, is rationally constructed on single‐crystalline LiNi0.9Co0.05Mn0.05O2 (SC90) for ultrastable mechanical integrity. Intensive in/ex situ characterizations combined with theoretical calculations and finite element analysis suggest that the uniform MTO coating layer prevents direct contact between SC90 and organic electrolytes and enables rapid Li‐ion diffusion with depressed Li‐deficiency, thereby stabilizing the interfacial structure and accommodating the mechanical stress of SC90. More importantly, a superstructure is simultaneously formed in SC90, which can effectively alleviate the anisotropic lattice changes and decrease cation mobility during successive high‐voltage de/intercalation processes. Therefore, the as‐acquired MTO‐modified SC90 cathode displays desirable capacity retention and high‐voltage stability. When paired with commercial graphite anodes, the pouch‐type cells with the MTO‐modified SC90 can deliver a high capacity of 175.2 mAh g−1 with 89.8% capacity retention after 500 cycles. This lattice‐matching coating strategy demonstrate a highly effective pathway to maintain the structural and interfacial stability in electrode materials, which can be a pioneering breakthrough in commercialization of Ni‐rich cathodes.

Sustainable Low-Temperature Coating of LATP/C Solid Electrolyte Composites on LiNi1/3Co1/3Mn1/3O2 Cathode Based on Lithium Iodide Solvent-Recrystallization for Li-Ion Batteries

Enhanced Electrochemical Performance of LiNi0.8Co0.15Al0.05O2 Cathode Material via Li2TiO3 Nanoparticles Coating

Enhancing the Electrochemical Performance of High Voltage LiNi0.5Mn1.5O4 Cathode Materials by Surface Modification with Li1.3Al0.3Ti1.7(PO4)3/C

Improving low-temperature performance of spinel LiNi0.5Mn1.5O4electrode and LiNi0.5Mn1.5O4/Li4Ti5O12full-cell by coating solid-state electrolyte Li-Al-Ti-P-O

Improving the electrochemical performance of Li1.2Ni0.13Co0.13Mn0.54O2 by Li-ion conductor

Mechanical alloy coating of LATP decorated porous carbon on LiFe1/3Mn1/3Co1/3PO4/C composite cathode for high-voltage Li-ion battery

Surface modification of Ni-rich LiNi0.8Co0.1Mn0.1O2 cathode materials via a novel mechanofusion alloy route

Surface Coating with Li-Ti-O to Improve the Electrochemical Performance of Ni-rich Cathode Material

In Situ Constructing Ultrastable Mechanical Integrity of Single‐Crystalline LiNi0.9Co0.05Mn0.05O2 Cathode by Interior and Exterior Decoration Strategy

A Low-Temperature Coating Method with H3BO3 for Enhanced Electrochemical Performance of Ni-rich LiNi0.82Co0.12Mn0.06O2 Cathode

One-pot synthesis and multifunctional surface modification of lithium-rich manganese-based cathode for enhanced structural stability and low-temperature performance

LATP-coated LiNi 0.8 Co 0.1 Mn 0.1 O 2 Cathode with Compatible Interface with Ultrathin PVDF-reinforced PEO-LLZTO Electrolyte for Stable Solidstate Lithium Batteries

Enhancing Electrochemical Performance of LiNi0.6Co0.2Mn0.2O2 by Lithium-ion Conductor Surface Modification

Stabilizing a high-voltage LiNi0.5Mn1.5O4 cathode towards all solid state batteries: a Li-Al-Ti-P-O solid electrolyte nano-shell with a host material

Facile Synthesis and Enhanced Electrochemical Performances of Li2tio3-Coated Lithium-Rich Layered Li1.13ni0.30mn0.57o2 Cathode Materials for Lithium-Ion Batteries

Mixed Electronic and Ionic Conductor-Coated Cathode Material for High-Voltage Lithium Ion Battery

Enhanced Interfacial Kinetics and High-Voltage/High-Rate Performance of Licoo2 Cathode by Controlled Sputter-Coating with A Nanoscale Li4ti5o12 Ionic Conductor

In-situ Formation of Hybrid Li3PO4-AlPO4-Al(PO3)3 Coating Layer on LiNi0.8Co0.1Mn0.1O2 Cathode with Enhanced Electrochemical Properties for Lithium-Ion Battery

LATP-coated LiNi0.8Co0.1Mn0.1O2 cathode with compatible interface with ultrathin PVDF-reinforced PEO-LLZTO electrolyte for stable solid-state lithium batteries

Manipulation of an ionic and electronic conductive interface for highly-stable high-voltage cathodes

Enhanced Electrochemical Performance of LiNi1/3Co1/3Mn1/3O2 at a High Cut-Off Voltage of 4.6 V by Li1.3Al0.3Ti1.7(PO4)3 Coating